Manual Texas BCU26S (page 14 of 45) (English, German, Danish, French, Polish)

636721

Zoom out

Zoom in

1/45

Refuel (Smoking prohibited)

! Mix and store the fuel in containers that are approved for the purpose.

! Mix the fuel outdoors where there are no sparks or flames.

! Choose a bare place, turn off the engine and leave it to cool for 2 minutes before refueling.

! Untighten the lid slowly to let out any pressure and to avoid that any fuel spills out under the lid.

! Wipe off any spilled fuel. Move more than 3 meters away from the place where you put fuel on the

engine before it is started.

Start / Stop.

How to start a cold engine

1. Place the brush cutter on a flat surface.

2. Switch to” I ”.

3. Press 8-10 times on the fuel pump located beneath the air filter.

Switch the choke in to start position see Fig.6-A

4. Activate the safety handle and press the throttle control, then lock the handle with the locking pawl.

Fig.6-B

5. Pull the starter until the engine runs.

Slide the choke lever to drive position when the engine starts to be warm

How to start a warm engine

Switch or ensure that the choke lever is set in driving position, see Fig.6-A

1. Pull the recoil starter until the engine runs.

How to stop the engine

1. Release the gas and the safety switch. Fig.6-B

2. Set the switch in the “ O ” position

Replacement the trimmer cord

Follow the procedure as shown in Fig.5

1. Stop the engine.

2. Press on each side of the line compartment. The lid may now be removed.

3. Dismount the roll simply by pulling it. Leave the spring (B), on the spool. Remove any bits of line.

Attach 3-4 meters of new line (2,4 mm) and place it double.

4. Fit each end of the line into a hole on the spool. Wind the two ends of line in the direction of the

arrow. Avoid twisting the line. Finally cut the double line at the middle. Fit the two ends through the

line controllers. Do not overfill the spool!

5. Mount the line compartment in reverse order. First, fit the spring into its position. Then place the line

in the two holes of the line compartment.

6. Finally mount the lid. Make sure that it is fitted securely.

Always make sure that the trimmer head is fitted securely. If in doubt ask your local dealer for advice.

Operation

 High grass should always be cut from the top and downwards. In this way you prevent the grass

from being wrapped around the trimmer head and thereby lead to overheating and damage. If grass

and the like is wrapped around the trimmer head the engine must be STOPPED, the spark plug cap

taken off and the grass then removed.

 For moving the line forward you tap the trimmer head lightly against the ground while the engine

runs at full speed.

 Hold the trimmer at an angle towards the area that is to be cut.

 The illustration shows the best cutting angle (Fig7A).

 Use the line to cut. Do not force the trimmer head into grass that has not yet been cut.

 Wire and fences are hard on the line and may even cause it to break.

Stones and walls, and wood cause the line to be worn down very fast. Walk around trees and bushes.

Bark and trees, wood boarding and poles are easily damaged by the line

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Texas BCU26S in the language / languages: English, German, Danish, French, Polish as an attachment in your email.

The manual is 1,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Texas BCU26S Manual

Product: