636721

Texas BCU26S Manual

13
Zoom out
Zoom in
Previous page
1/45
Next page
13
Changing from trimmer to brush cutter
Remove the trimmer head Follow the procedure as shown in Fig.4-B
1. Mount the holder(4) in the hole by trimming gear(3), and bearing(2) secure to the shaft.
2. Demount the trimmer head (1) from the shaft.
Notice: Keep the parts for the trimmer head together for later use.
Mounting of blade. Follow the procedure as shown in Fig.4-A
1. Fit the holder (7) in the hole of the trimmer gear (9),and the bearing(5) so that is fastens the axle.
2. Fit the blade (6) and the washer (4) onto the axle.
3. Fit the washer (3) and nut (2). Fasten tightly anticlockwise.
Ensure that the blade is tightly fastened. If unclear ask your local dealer for advice.
Changing from brush cutter to trimmer
Dismounting the blade
Follow the procedure as shown in Fig.4-A
1. Remove the pin (1) Fit the holder (7) in the hole of the trimmer gear(9),and the bearing(5) so that it
fastens the axle.
2. Remove the nut (2),that fastens the blade.
3. Washer (3), spacer (4) and blade (6) may now be removed.
Notice: Store the parts together for later use.
Mounting of trimmer head.
Follow the procedure as shown in Fig.4-B
1. Mount the holder (4) in the hole by trimming gear (3), and bearing (2) secure to the shaft.
2. Mount the trimmer head (1) onto the shaft and fasten.
Fuel
This product is equipped with a two-stroke engine that demands two-stroke oil added to the petrol.
Always use unleaded gasolinee.
Never use ready-mixed gasoline/oil from service stations that is normally used for mopeds,
motorbikes, etc.
Always follow the directions of the supplier for the oil regarding the mix of oil (see the back of the oil
container).
Use a clean and approved petrol can for mixing the petrol with oil.
Use an approved two-stroke oil for air cooled engines, chainsaws, trimmers etc. (Do not use oil for
out board engines of cars. (Mix only small quantities).
Normally 2,5% oil is mixed with the gasoline. (40:1) however, always follow the directions of the
manufacturer of the oil.
Mix the oil and gasoline thoroughly and shake the can before filling.
Never use a mix of gasoline and oil that is more than 90 days old as this may lead to problems when
starting the engine. Never store the same mixture in the tank for more than 30 days.
When storing the machine for more than 30 days you should empty the tank.
Filling of petrol - Smoking prohibited!
1. Unscrew the petrol lid. Place it on a clean surface.
2. Carefully pour the oil mixed fuel into the tank. Beware of spilling.
3. Screw the lid on tightly. Wipe away any spilled fuel.
4. It is normal that the engine smokes the first time it is used.
Notice! Always turn off the engine before fuelling. Never put fuel on a machine that is running or when the
engine is hot (cooling time at least 2 minutes). Move more than 3 meters away from the place where you put
fuel on the engine before it is started.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas BCU26S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas BCU26S in the language / languages: English, German, Danish, French, Polish as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info