636718

Texas BC 335-4 Manual

21
Zoom out
Zoom in
Previous page
1/69
Next page
21
11. Kickback is a reaction that can occur when a rotating blade comes into contact with
something it cannot cut. This can cause the blade to stop for a moment, causing the
machine to recoil from the object it hit. This reaction can be so violent that control
over the machine can be lost. Kickback can occur without warning if the blade gets
stuck, loses speed or is impaired. This is more likely to occur in areas where it can
be hard to see the material to be cut.
12. Always ensure strap is properly adjusted.
13. Maintain a firm grip on both handles while blade is in use. Keep blade away from
body and under waist height.
6. Switch from Brushcutter to Trimmer
Removing blade - figures 6, 7, 8.
1. Insert the Allen wrench (1) provided into trimmer gear hole and bushing (a) to
secure the shaft.
2. Screw off the nut (f).
3. Remove lock ring (e), cup (d), washer (c) and blade (b).
Note! Keep blade parts together for later use.
Fitting trimmer head – figures 14, 15, 16, 17.
1. Mount bushing (a)
2. Place the provided allen wrench (1) in the hole in the gearhousing, make sure it
goes through the hole in the bushing (a), so it is locked.
3. Mount the trimmerhead (c) (turn counterclockwise), make sure it is tightenen
proberly.
4. Remove the allenwrench before use.
7. Replacing Cord
1. Stop engine.
2. Press each side of cord housing. Remove lid.
3. Remove roll by pulling. Allow spring to remain on spool. Remove any cord residue.
Take 3-4 m of cord (2.4 mm) and double it up.
4. Insert both ends into the 2 holes on the roll. Wind cord onto roll in direction of arrow.
Avoid twisting cord. When twine is fully on roll, cut and insert the two cut ends
through the guide holes.
5. Assemble cord housing in reverse order, starting with spring. Place cord in cord
housing holes.
6. Re-place cover. Check cover is secure.
Figure 10.
Always ensure trimmer head is secured tightly.
NEVER OVERFILL THE REEL!
If in doubt, contact your nearest dealer.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas BC 335-4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas BC 335-4 in the language / languages: English, German, Danish, French as an attachment in your email.

The manual is 1,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info