649682
65
Zoom out
Zoom in
Previous page
1/164
Next page
- 65 -
- if necessary or requested by the vehicle
manufacturer speci cations, customise the
voltage and/or current values as indicated below;
- use the “VOLT” button to select the battery voltage;
- connect the clamps to the relative vehicle battery
terminals;
- the process will run automatically indicating the
voltage value on the display ( g. A.2), along with
the current ( g. A.4) after 5 seconds from the last
operation.
DISPLAY - EXAMPLE
3.6.2 SUPPLY
Constant voltage generator that can be used on
BATTERY CHANGES or on batteries with a very
low voltage (below 2V) to try to increase their
voltage to a value that is suitable for starting with a
normal charge cycle.
FUNCTION SELECTION
DISPLAY
ATTENTION! The set voltage is always
present on the charge clamps even when
disconnected from the battery.
ATTENTION! Pay particular attention to
thenominalvoltage of thebatterywhichmust
correspond to the voltage selected using the
“VOLT”buttonandindicatedonthedisplay(g.
A.1). This function DOES NOT FORESEE spark
protection on the output clamps and polarity
reversal.
Customising VOLTAGE and CURRENT
VOLTAGE
- press and hold simultaneously the “VOLT” ( g.
A.21) and “FUNCTION” buttons ( g. A.22) for 3
seconds
- use the same buttons to select (decrease
using the “VOLT” button and increase using
the “FUNCTION” button) the desired voltage
value between 6V÷7.5V, 12V÷15V, 24V÷30V
respectively for 6V, 12V, 24V batteries; the factory
default voltage value is respectively 6.8V, 13.6V,
27.2V.
The set voltage mode will be exited automatically
after a 3” time-out.
VOLTAGE ADJUSTMENT - EXAMPLE
3"
BEEEP
DISPLAY
13.3V
13.2V
13.1V
. . . . .
. . . . .
13.7V
13.6V
13.5V
CURRENT:
- press the “MODE” button until the desired value,
set as indicated in step 6, appears on the display
( g. A .4) and on the icon ( g. A.6). The set current
mode will be exited automatically after a 3” time-
out.
CURRENT ADJUSTMENT - EXAMPLE
3A 7A 10A 20A 30A 40A
3A 7A 10A 20A 30A 40A
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telwin DOCTOR CHARGE 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telwin DOCTOR CHARGE 50 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 9,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info