649682
60
Zoom out
Zoom in
Previous page
1/164
Next page
- 60 -
c) CUSTOMISED PULSE-TRONIC
It is possible to select:
- the battery construction technology ( g. A.11)
choosing between:
“WET, GEL, AGM, PbCa”
- the charge current ( g.A.6) choosing between:
“AUTO” - automatic setting according to battery
conditions;
“BOOST” - rapid charge;
- the Ah - customised setting of the battery Ah ( g.
A.2) using 6 prede ned values selected using
the “MODE” button ( g. A.23), adjustable at 5 Ah
intervals using the “VOLT” button ( g. A.21), and
“FUNCTION” ( g. A.22).
Ah SETTING - EXAMPLE
15Ah 100Ah 300Ah
15Ah 100Ah 300Ah
DISPLAY
80Ah
75Ah
70Ah
. . . . .
. . . . .
100Ah
95Ah
90Ah
Note. The  nal charge voltage depends on the
technology of construction of the battery; to avoid
damaging the battery, pay special attention to the
technical speci cations given by the manufacturer.
Construction
Technology
Final charge voltage
6V 12V 24V
WET 7.7V 15.4V 30.8V
GEL 7.2V 14.4V 28.8V
AGM 7.35V 14.7V 29.4V
PbCa 8V 16V 32V
AUTO 7.2V 14.4V 28.8V
AUTO
7.7V 15.4V 30.8V
The PULSE TRONIC charge process ( g. A.17)
starts when the display stops ashing, each
individual phase is identi ed on the display ( g.
A.14) and terminates with the message ( g. A.2)
“OK”. The battery charge status is displayed
graphically in ( g. A.5). If the charge process is
not successful, an alarm message appears on
the display ( g. A.2) (see alarms list). When the
battery is charged, the battery charger switches
automatically to maintenance mode.
END OF CHARGE - EXAMPLE
CHARGE COMBINATION CHART
BATTERY TYPE
(T)
BATTERY CURRENT
(C)
AUTO
AUTO
AUTO BOOST
MANUAL “Ah”
AUTO
AUTO
AUTO BOOST
MANUAL “Ah”
WET
GEL
AGM
PbCa
AUTO
AUTO BOOST
MANUAL “Ah”
3.3.2 STORING OPERATION SETTINGS
It is possible to store the last function modes, so
they are immediately available after any switching
ON/OFF.
3.3.2.1 STORING PULSE-TRONIC CHARGE
Storage of voltage and type of battery, charge
mode.
Procedure:
- Check that the charge clamps are not connected
to a battery;
- Connect the power cable to the mains socket;
- Set the desired charge mode;
- Disconnect the power cable from the mains
socket.
3.3.2.2 STORING SUPPLY/DIAGNOSTIC
MODE
Storage of delivered voltage and current.
Procedure:
- Set the chosen mode and adjust the voltage/
current values as required;
- Turn on the lock settings by pressing, at the same
time, both keys “VOLT” ( g.A.21) and “MODE”
( g.A.23) for 3 seconds, on the display ( g.A.2)
( g.A. 4) will appear “LOK on.”
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telwin DOCTOR CHARGE 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telwin DOCTOR CHARGE 50 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 9,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info