Manual Telair Energy 2510D (page 15 of 44) (English)

688848

Zoom out

Zoom in

1/44

Vers. 002

Energy 2510 D

7.1 Starting up the generating set

Before the first start-up check the oil level.

Set the start-up switch (fig. 24 ref. 1) to “ON”

position. The word “WAIT” will appear on the

display for 8 seconds. When these have run out,

the electronic control panel will start the first

automatic procedure for starting up the

generating set. If the engine starts up at the end

of this phase, then the “generator running”

indicator

(fig. 24 ref. 6) will start to flash.

Should the engine not start up, this automatic

procedure will be repeated up to 4 times. If the

engine has not started up yet at the end of this

complete cycle, the “start-up failed” indicator

( fig.

24 ref. 5) will light up to signify that the

generating set has failed to start up.

If only the “start-up failed” indicator

(fig. 24 ref. 5)

stays lit, you can repeat the start-up procedure

several times.

If the generating set has not started up at all

even after many attempts, you will have to get in

touch with the After-sales service.

7.2 Turning the generating set off

To stop the generating set, set the "ON/OFF”

switch to "OFF" position (fig. 24 ref. 1).

Always turn the

generating set off after disconnecting the load

7.3 Control and alarm functions (Fig. 24)

2 Display unit: when the generating set has

started up, the total running hours will be

displayed. Press the button (fig. 12 ref. 9) to

display the partial running hours of the

generating set since the latest engine oil change.

3 High temperature indicator: this pilot lamp

will light up when the temperature of the

generating set goes over its safety value; the

engine will stop.

4 Minimum engine oil level indicator: this pilot

lamp will light up to indicate that the oil in the

engine has gone below the minimum level; the

engine will stop.

5 Engine start-up failed indicator: this pilot

lamp will light up to indicate that the generating

set has not started up, after all four attempts at

starting up have failed.

7 Engine oil change indicator: this pilot lamp

will light up when the engine has reached 100

running hours since the latest oil change. Upon

every engine oil change the After-sales service

staff must reset the Timer to make it restart from

zero.

8 Fuel reserve indicator: this pilot lamp will light

up when the fuel level has gone below its reserve

level (about 4 litres) inside the extra tank.

9 Display changeover switch: press this button

to display the running hours elapsed after the last

change of the engine oil.

10 Reset: this key (not visible) is used to reset

the panel (operation to be done only if the panel

has inexplicable behavior or the display shows

characters without any logic).

7.3.1 Control panel alarm causes and

resetting

During generating set use, alarm signals may be

displayed referring to engine oil checks. After

checking the engine oil, the control panel must

be reset in the following way:

Alarm: the red ‘service’ light is flashing.

Cause: 50 hours have elapsed since the latest

engine oil change and oil level should be

checked.

How to reset the alarm: with panel turned off,

press the partial counter key (Fig.30 Ref.9) and

while holding it down, turn the panel on and

release the push-button when the unit has

started up

Alarm: the red ‘service’ light is lit.

Cause: 100 hours have elapsed since the latest

engine oil change and engine oil should be

changed.

How to reset the alarm: turn on the panel and

wait for the generating set to start. Now press the

button hidden under the small hole in the bottom

left corner (Fig.30 Ref.10) and release it

immediately thereafter.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Telair Energy 2510D in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Telair Energy 2510D Manual

Product: