Manual Telair Energy 2510b (page 20 of 40) (English)

688849

20

Zoom out

Zoom in

Previous page

1/40

Next page

Energy 2510 B

Vers. 002

GB

20

has inexplicable behavior or the display shows

characters without any logic).

6.6 Control panel alarm causes and resetting

During generating set use, alarm signals may be

displayed referring to engine oil checks. After

checking the engine oil, the control panel must

be reset in the following way:

Alarm: the red ‘service’ light is flashing.

Cause: 50 hours have elapsed since the latest

engine oil change and oil level should be

checked.

How to reset the alarm: with panel turned off,

press the partial counter key (Fig.30 Ref.9) and

while holding it down, turn the panel on and re-

lease the push-button when the unit has started

up

Alarm: the red ‘service’ light is lit.

Cause: 100 hours have elapsed since the latest

engine oil change and engine oil should be

changed.

How to reset the alarm: turn on the panel and

wait for the generating set to start. Now press the

button hidden under the small hole in the bottom

left corner (Fig.30 Ref.10) and release it immedi-

ately thereafter. Wait a couple of minutes before

turning the generating set off.

Alarm: the display unit shows random charac-

ters.

Cause: malfunctioning due to low voltage during

start-up (low battery, cable cross-section too

small). In this case, just turn Off and On the con-

trol panel.

In certain situations, data of internal microproc-

essor of the panel may be subject to permanent

alterations and prevent running of generating set.

In this case, to restore the functionality of panel is

necessary to completely re-initialize (contact the

Service).

6.7 Automatic Version (optional)

If you wish the start-up batteries to be recharged

automatically in the En 2510 B generating sets, it

is possible to install the ASP (optional) automatic

control panel (fig.32) instead of the manual con-

trol panel.

The elements making it up are:

1 ON/OFF switch for the start-up and switch-off

function

2 Display

3 High temperature indicator

4 Minimum oil level indicator

5 Start-up failed indicator

6 Generator running indicator (flashing)

7 Maintenance request indicator

8 Fuel reserve indicator

9 Hour or voltmetric changeover switch button

10 Reset

11 Battery charged indicator

12 Automatic function indicator

13 AUTO/MAN switch for the automatic or man-

ual function

6.8 MANUAL operation

See section 6.1

6.9 AUTOMATIC operation

Turn the AUTO/MAN switch (Fig.32 Ref.13) to

the AUTO position and set the start-up switch

(Fig. 32 Ref. 1) to ON position.

The automatic function indicator (Fig.32 Ref.12)

will light up.

When the voltage at the ends of the 12V DC ter-

minals of the generating set is lower than 11.5

Volts, the generating set will begin the start-up

procedure (similar to that of the manual opera-

tion).

During the operation in automatic mode, the dis-

play (Fig.32 Ref.2) will show the total running

hours of the generating set. Press the hour or

voltmetric changeover switch button (Fig.32

Ref.9) to display the voltage at the ends of the

12V DC terminals, i.e. at the ends of the battery.

When the battery is charged, and anyway after at

least 15 minutes’ running, the battery charged

hours indicator (Fig.32 Ref.11) will light up and

1

Hello,
I can not get start on my Telair Energy 2510b. It seems to me that the fuel do not reach the "engine".
Fuel pump?

Det ser ikke ut som bensinen suges fra bensintanken. Kan dette være årsaken og evnt.hva må gjøres?
Jeg tatt service, skiftet olje, skiftet tennplugg og rengjort luftfilter.

mvh
Thor, +4795972210
thor@jemtland.no

Submitted on 8-7-2022 at 08:48
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Telair Energy 2510b at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Telair Energy 2510b in the language / languages: English as an attachment in your email.

The manual is 4,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info