487279

Team SIS 3 Manual

15
Zoom out
Zoom in
Previous page
1/48
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don‟t change
the page numbering. Keep the language integrity.
15
Assembly page 15/48
Fax +32 2 359 95 50
FILLING THE WATER TANK DURING USE
As the water tank of this appliance is not under pressure, you can refill it during use. To dos o,
just proceed as described above in the "Filling with water" section).
STEAM-IRONING
Fill the water tank with water and insert the mains plug into a wall socket.
As indicated on the temperature dial (4) and the table, steam ironing is only possible at
higher ironing temperatures, so set the dial to  or .
When you plug in the appliance, the power light (5) of the control panel will go on and will
stay on permanently (= standby mode) whereas the pilot light (6) will be off. Pres the reset
button (8) so that the water starts to heat. The pilot light (6) will start blinking (= initial
mode). As soon as the temperature necessary for steam production is reached, the pilot
light will stop blinking and stay on (= working mode). The 15-minute auto shut off function
switches on (see "Auto shut off function" section below). In the meantime the pilot light of
the lowest steam output will go on. You can now use the steam function.
Press the steam button (2) to release steam from the soleplate of the iron. Release the
button and the steam will stop. If you want a continuous jet of steam, slide the central part
of the steam button backwards till it blocks the steam button. To stop the steam, slide the
lock-on button (1) forward to block the steam button. To stop the steam, slide the lock-on
button backward to release the steam button.
To set the desired steam output, press the steam regulator (9). Each time you press the
button the steam output will switch to another output in the following order: (low) –
(medium), - (high), you will hear a beep and the corresponding pilot light will
come on on the control panel, indicating the set steam output. To come back to a low
steam output, press the steam regulator (9) once more.
When ironing, the pilot light of the iron (3) will go on and off from time to time. This means
that the temperature of the iron is regulated by its thermostat. You can continue ironing.
When you use a lot of steam in a very short time, the steam output is lightly reduced until
your appliance produces enough steam to reduce the difference. This phenomenon also
happens when there isn‟t enough water in the water tank.
When the water tank is running empty, you will hear more noise when pressing the steam
button. If you want to go on using the steam function, you will have to refill the water tank.
STEAMING IN A VERTICAL POSITION
You have to hang the cloth you want to smooth out avoiding the creases and place the iron in
a vertical position at a few centimetres from the piece of cloth. Then move the iron by pressing
the burst of steam button.
DRY IRONING
For ironing without steam, do not press the steam button (2) and do not pres the lock-on
button (1).
Take the "Auto shut off function" section below into consideration.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team SIS 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team SIS 3 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info