487279

Team SIS 3 Manual

14
Zoom out
Zoom in
Previous page
1/48
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don‟t change
the page numbering. Keep the language integrity.
14
Assembly page 14/48
Fax +32 2 359 95 50
During ironing this pilot light (3) will come on from time to time. When this happens, the
soleplate is being heated-up to the required temperature again. You can continue
ironing.
The table is valid for the fibre materials only. If some kind of finish has been applied (gloss,
wrinkle, relief etc), the textile can best be ironed at a lower temperature.
First sort out the fabrics according to ironing temperature: wool with wool, cotton with
cotton, etc.
The iron heats up quicker than it cools down. Therefore, start ironing the articles requiring
the lowest temperature such as those make of synthetic fibres. Then progress to the higher
temperatures.
If the article is made of a mixture of different fibre, you must always select the lowest
ironing temperature of the composition of those fibres.
(E.g. an article consisting of “60% polyester and 40% cotton” should be ironed at the
temperature indicated for polyester and without steam).
If you do not know what kind(s) of fabric(s) the article has been made of, find a spot,
which will be invisible when wearing or using the article to try out the ironing temperature.
(Always start at a low temperature and increase to one, which gives the required results).
Pure woollen fabrics (100% wool) may be pressed with the iron set to a steam position. It is
recommended to apply shot-of-steam and use a dry pressing cloth.
When steam-ironing woollen fabrics, shining of the fabric may occur. This can be
prevented by turning the article inside out and ironing the inside or by interposing a light
damp cloth.
Velvet and other textures that rapidly acquire shiny spots should be ironed in one direction
only (with the nap), applying only light pressure.
Always keep the iron moving.
Iron the reverse side of synthetic materials and silk, it is not advisable to use steam as this
may cause stains.
FILLING WITH WATER (FOR STEAM-IRONING)
1. Put the base on a stable surface.
2. Open the cap of the water tank and fill it with clear water up to its "Max" level. You can
use tap water, but we advise you to use demineralised water.
3. Close the cap of the water tank
or
4. You can detach the water tank by lifting it, and then fill it as described by steps 2 and 3
above.
5. Put the water tank back in the base correctly. Caution, if the water tank is not positioned
correctly, a safety device will prevent the pump from operating and as a result, it will
prevent the steam production. If this happens, check whether the water tank is placed
correctly on the base.
6. Never use vinegar, detergents or other chemical products.
Caution: always make sure that the anti-scale cartridge situated underneath the water tank is
well into place. Never use the appliance without anti-scale cartridge.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team SIS 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team SIS 3 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info