587255
60
Zoom out
Zoom in
Previous page
1/68
Next page
Mixer
amount of time until gain reduction is fully-functional, and Soft applies a soft knee
for extreme ratio settings. On turns the effect on and off and Gain is a post-
compressor makeup stage.
• The Equalizer section houses a four-band full-parametric EQ section. The On button
at the top-right corner of this panel switches the EQ on, and the On button above
each band switches that band on. (Note that you need to press two On buttons to hear
EQ, the master ON button and one band’s ON button.) The Type pulldown menu
gives you a choice of Low Shelf, High Shelf, Peaking, Low Pass and High Pass for
each band. You can use the Gain, Frequency and Q knobs to change EQ, or grab the
dots in the graphic display.
Mixer Tabs
There are five tabs at the bottom of the VGA display:
Tracks is the track/waveform view (or press F1)
Ch. 1-24 jumps to the first 24 channels of the mixer (or press F2)
Ch. 25-48 jumps to the second 24 channels of the mixer (or press F3)
Groups jumps to the subgroups and aux returns (or press F4)
Masters jumps to the Master output (or press F5)
All of the mixer channels, groups and masters are located in one large window, so you can
see channels 12-35 if necessary.
Automation
To display automation, click the button pictured above or press Alt-A. You can automate the
level of a track using this automation, and also play back automation from imported
projects. The edit tools change in this mode:
• Use the Cursor tool (click the "+" button or press F8) to write automation. Click and
drag on a track to write new automation points.
If you mouse over one of the automation points with the Cursor tool, your cursor
turns into the Finger tool. Click and drag any automation point to change its level or
time position.
In automation mode, the Smart tool becomes an Eraser so that you can delete
automation entries.
• Use the I-beam tool to select automation. You can cut, copy, paste or delete
automation from the keyboard or Edit menu.
External Control
The X-48 supports the TASCAM US-2400 as a mixing control surface. Connect the US-
2400 to the USB input and set its control mode to Native by holding Select and Channel
during power up. The US-2400 controls the X-48’s transport, fader levels, pan, aux sends,
bank select channels, and more.
60
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam X-48 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam X-48 in the language / languages: English as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info