587255
17
Zoom out
Zoom in
Previous page
1/68
Next page
Setup
requires a specifically constructed cable. If in doubt, pre-made RS-422 cables are readily
available.
1 : GND 6 : GNC
2 : TX- 7 : TX+
3 : RX+ 8 : TX-
4 : GND 9 : FGND
5 : NC
Video Reference (Tri Level Sync)
IN – When the X-48 is used in a film/video post production environment, it may be
necessary to resolve a consistent sample range with the time code edge. A video reference
(blackburst) signal applied to this connector makes this possible. Please refer to page 48 for
details on configuring the use of signals present at this connector.
Tri Level Sync is the video reference signal used for High Definition Video. This connector
automatically senses the type of signal present.
THRU – The video reference signal present at the IN connector is passed through out this
connector without additional processing delay. This allows for daisy-chaining another
device, after the X-48, which requires a video reference signal.
Keyboard, Mouse & Monitor
A standard PC keyboard & mouse (or trackball) may be connected to the P/S2 or USB ports
on the rear of the X-48. To take full advantage of these peripherals, it is recommended that
a full keyboard with numerical keypad and a scrolling wheel mouse be used.
NOTE: The extra controls present on some multi-media keyboards, such as media player
transport controls, are not supported by the X-48. Similarly, a mouse or trackball that
depends on the installation of custom driver software is not supported by the X-48.
Your monitor should be capable displaying a resolution of at least 1024x768
pixels at a refresh rate of at least 60 Hz. The maximum resolution of the X-48's
display output is 2048x1536 pixels.
Network
The X-48 is equipped with two separate Network connectors on the rear panel. One is a
10/100 port and the other is a 10/100/1000 (Gigabit) port. The 10/100 port is pre-configured
as a DHCP port. The Gigabit port may be configured by the user in the X-48’s software.
Network cable used for these ports should be minimally CAT-5. While network hubs and
switches can be used with the X-48, such devices may reduce network throughput,
particularly on a network with much traffic.
When using the pre-installed MX-View software to control MX-2424 machines, the Gigabit
port must be used and configured to the correct IP address to communicate with the MX-
2424s.
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam X-48 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam X-48 in the language / languages: English as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info