617900
46
Zoom out
Zoom in
Previous page
1/64
Next page
46 TASCAM HS-P82
System settings (SYSTEM SETUP)
Make system settings on this screen.
The
SYSTEM
SETUP
screen has 3 pages:
PREFERENCES
,
ALARM
TONE
and
CLOCK
ADJUST
. Touch the tabs at the
bottom of the screen to open the corresponding page.
PREFERENCES page
Set system preferences on this page.
KBD Type
Set the connected keyboard type.
Setting buttons:
US
(default setting) and
JPN
Solo Mode
Set the solo mode.
Set to “Single” to solo one track at a time or “Mix” to allow
more than one track to be soloed at the same time.
Setting buttons:
Single
(default setting) and
Mix
Slate Type
Set whether the slate signal is input from the built-in mic or
is a tone signal.
Setting buttons:
INT
MIC
(default setting) and
TONE
Ref. Level
Set the reference level for analog input and output to a
number of decibels below the maximum level (full bit rate
utilization).
Setting buttons:
9dB
,
14dB
,
16dB
(default value),
18dB
and
20dB
ALARM TONE page
Make alarm settings.
Write Error
Set whether or not an alarm sounds when there is a write
error. (Default setting:
ON
)
Input Clip
Set whether or not an alarm sounds when the input exceeds
the maximum. (Default setting:
OFF
)
Battery Caution
Set whether or not an alarm sounds when the battery voltage
becomes low. (Default setting:
ON
)
CF Remain Caution
Set whether or not an alarm sounds when the remaining
amount of time on the CF card becomes low. (Default
setting:
ON
)
Touch the knob and when its background color turns yellow,
use the DATA dial to adjust the amount of remaining time
setting. The setting value range is 1–9 minutes. (Default
value:
3 min
)
The alert sounds have the following patterns.
Alert sound patterns
CLOCK ADJUST page
Set the time of the built-in clock.
Touch the item that you want to set. Use the DATA dial to
adjust the item. When you finish setting the items, press the
DATA dial or touch the
SET
button on the
CLOCK
ADJUST
page to confirm the setting.
NOTE
While setting the time, the clock stops and the “:” does not
blink. When you touch the SET button, the clock starts again
and the “:” blinks.
6 – Internal Settings and Operations
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-P82 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-P82 in the language / languages: English as an attachment in your email.

The manual is 8,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info