617905

Tascam HS-8 Manual

46
Zoom out
Zoom in
Previous page
1/72
Next page
46 TASCAM HS-8
MASTER
Select the master clock to use.
INT (default value): Use this unit’s internal clock.
WORD: Synchronize with the word clock input through
the WORD/VIDEO IN connector.
VIDEO: Synchronize with the video clock input through
the WORD/VIDEO IN connector.
CH1-2DIN - CH7-8DIN: Synchronize with the clock of the
digital signal (AES1-8, AES A-B, or ADAT1-8) selected as
the digital input for CH1-2, 3-4, 5-6, or 7-8.
You cannot select an input as the master clock if the
sampling rate converter is ON for that input.
The second line of the button shows the name of the
selected digital input signal.
NOTE
A check mark appears on the button of the currently active
•
master clock.
If synchronization from an external clock is interrupted, the
•
unit’s internal clock becomes active. In this case, a check mark
appears on the INT button to show that it has become the
active clock, and an “x” appears on the button of the selected
external clock that was lost.
SYNC page
Make setting related to synchronization.
STATUS
Shows the status of the currently loaded project’s
sampling frequency and clock synchronization.
Play Fs
When playing a take with a sampling frequency of 48 kHz,
48 kHz pull-up, or 48 kHz pull-down, the unit can be made
to synchronize with an external clock by setting it to play
back with pull-up or pull-down.
Depending on the combination of Project sampling
frequency and Play sampling frequency settings, the unit
will operate with the Fs shown below.
Play sampling frequency setting
Project
sampling
frequency
OFF (Default
setting)
Pull-down Pull-up
48 kHz 48 kHz 48 kHz – 0.1% 48 kHz + 0.1%
48 kHz pull-up 48 kHz + 0.1% 48 kHz Not possible
48 kHz pull-
down
48 kHz – 0.1% Not possible 48 kHz
All others Project
sampling
frequency
Not possible Not possible
NOTE
Set this to OFF before recording. Recording is not possible when set
to Pull-up +0.1% or Pull-down –0.1%. If you try to record when not
OFF, “Cannot REC” appears in a warning pop-up window.
TC Chase
Use to turn playback synchronized with external timecode
ON/OFF (default value: OFF). Set it to ON, when you want
to match the timing of this unit’s audio with a timecode
master unit (audio recorder or video).
You can also set timecode offset (TC Offset) with the
timecode master device. Touch the “EDIT” button to open
the “TC Offset” screen where you can set the offset value
in a range between “−23: 59: 59.29” and “+23: 59: 59.29”
(default value: “00: 00: 00.00”).
NOTE
TC Chase can also be turned ON/OFF by pressing the SHIFT and
CALL keys at the same time.
TC Rechase
Turn this function, which re-synchronizes when
synchronization with external timecode becomes
inaccurate, ON/OFF (default value: “OFF”). To set the
amount of inaccuracy that triggers rechase, touch the
knob and turn the DATA dial to select a value in frames of
1/3, 1, 2, 5 or 10 (default value: 2 frames).
T/C page
Make settings related to time code.
Free run mode
6 – Internal Settings and Operations
… 46 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-8 in the language / languages: English as an attachment in your email.

The manual is 4,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info