617905
48
Zoom out
Zoom in
Previous page
1/72
Next page
48 TASCAM HS-8
Remote settings (REMOTE SETUP)
Make settings for PARALLE connector AUX 1-3 functions
and the RS-232C and RS-422 control connectors. The
REMOTE
SETUP
screen has a
PARALLEL
page, an
RS-232C
page, and an
RS-422
page. Touch the tabs at the bottom
of the screen to open the corresponding page.
PARALLEL TAB
Set the AUX 1-3 functions of the PARALLE connector.
AUX Assign
Touch a knob, making the background become yellow
and turn the DATA dial to set the parameter. The
parameters that can be selected include
F.FWD
,
REW
,
MARK
,
MARK
SKIP-
,
MARK
SKIP+
and
ONLINE.
AUX1 Function: Set the function of PARALLEL connector
pin 17 (AUX1). (Default setting: MARK SKIP +)
AUX2 Function: Set the function of PARALLEL connector
pin 18 (AUX2). (Default setting: MARK SKIP –)
AUX3 Function: Set the function of PARALLEL connector
pin 19 (AUX3). (Default setting: MARK)
RS-232C page
Make RS-232C transmission settings.
Serial Mode
Set the serial connection mode with the following
buttons.
Setting buttons: “RS-232C” (default value), “RS-422”
NOTE
The RS-232C and RS-422 connectors cannot both be used at the
same time. Only the connector selected with this setting functions.
This setting is synchronized with the “Serial Mode” item on the
RS-422 page.
Baud Rate (bps)
Set the transmission speed. The options are 4800, 9600,
19200 and 38400 bps (default setting).
Data Length
Set the data length in bits. The options are 7 and 8 (default
setting).
Parity Bit
Set whether or not there is a parity bit. The options are
NONE
(default setting),
EVEN
and
ODD
.
Stop Bit
Set the stop bit. The options are 1 (default setting) and 2.
RS-422 page
Make communication settings for RS-422 serial control.
Serial Mode
Set the serial connection mode with the following
buttons.
Setting buttons: “RS-232C” (default value), “RS-422”
NOTE
The RS-232C and RS-422 connectors cannot both be used at the
same time. Only the connector selected with this setting functions.
This setting is synchronized with the “Serial Mode” item on the
RS-232C page.
Video Resolve
When slaving this unit to a VCR, video sync signals might
be used instead of word sync signals for the common
standard clock. In the same way as with word sync
signals, you can select whether the video clock is followed
(synchronizing the beginning of time code frames with
video signal frame edges) or it is independent of the
frame clock. This must be turned ON to control this unit
from a video editor.
Setting buttons: “OFF”, “ON” (default value)
6 – Internal Settings and Operations
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-8 in the language / languages: English as an attachment in your email.

The manual is 4,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info