650844

Superrollo RM10MSF Manual

22
Zoom out
Zoom in
Previous page
1/68
Next page
Starting up the device
22
Starting up the device
Before the device can be used, the following steps must be carried out:
■ Connect the motor cable to the mains power supply
■ Insert a 27A-12V battery into the remote control
■ Mount the roller shutter curtain on the winding shaft
■ Set the upper and lower terminal stop point.
Connecting the device
Connection of the tubular motor to the mains power and all work on electrical
systems may only be carried out by a certified specialist electrician according to
the connection schematics contained in these instructions.
DANGER
Fatal electric shock due to coming into contact with live
components.
¾ Do not carry out any connection work on the device when it is
connected to the current supply.
¾ Make sure that the device is disconnected from the mains power
supply.
ATTENTION
Malfunctions or damage to the motor due to incorrect mains
voltage.
¾ Compare the information on the model plate with that of your local
mains power supply.
¾ Make sure that the device is only connected to a 230 V ~ 50 Hz
mains power supply.
ATTENTION
Short-circuit due to damaged cables.
¾ Make sure that the cable cannot be damaged by moving parts in
the roller shutter box.
ATTENTION
Short-circuit due to water in the motor on routing cables
incorrectly.
¾ Never route the cable vertically upwards.
¾ Always route the cable in a loop.
Routing the cable in a loop enables the water to drip off (1.).
¾ Connect the motor cable to the current connection provided for this purpose.
Establishing the radio link
The remote control included in the scope of delivery is used to control the motor's
electronics by radio. This chapter provides information on establishing the radio
link between the remote control and the motor.
The basic requirement for the remote control function is a charged 27A-12V
battery in the battery compartment on the rear side of the remote control.
The indicator LED lights up when a button is pressed.
The following overview shows the remote control's controls and displays.
1
2
4
3
8 UP button A DOWN button
9 STOP button @ Indicator LED
Logging the remote control onto the motor (right-hand motor)
If the motor is installed on the right-hand side of the roller shutter box, the radio
link between the motor and the remote control is established in this way.
¾ Switch the motor off.
¾ Wait for approx. 10 seconds.
¾ Switch the motor on again.
A long beep is audibly emitted by the motor.
¾ Press button P2 (1) twice; this is located next to the battery compartment on the
rear side of the remote control.
1
¾ Press the UP button once.
Seven short beeps are audibly emitted by the motor.
Logging the remote control onto the motor (left-hand motor)
If the motor is installed on the left-hand side of the roller shutter box, the radio link
between the motor and the remote control is established in this way.
¾ Switch the motor off.
¾ Wait for approx. 10 seconds.
¾ Switch the motor on again.
A long beep is audibly emitted by the motor.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Superrollo RM10MSF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Superrollo RM10MSF in the language / languages: English, German, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 4,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info