480561

Strong SRT 8502 Manual

9
Zoom out
Zoom in
Previous page
1/21
Next page
6
Українська
Antenna Power: Use the tu to turn antenna power on / off/. Before connecting the
antenna, please read the User Guide for the antenna. If you use an active
internal or external antenna that requires power supply voltage of 5 V DC
and consumes less than 50 mA, then set it to On. Otherwise, set it to Off.
After all settings are made (including the adjustment of the antenna), press BLUE button on the remote
control to start scanning for channels.
The receiverwill start searching forchannels. On the screenwill be displayed information about the
scannedfrequency,foundTV and Radiochannels andchannel searchprogress. Once thechannel scanis
complete, the receiverwill turnon the first channel, whichis in the list.
NOTE: If at the end of the search the receiver did not found channels, it is
possible that your antenna is not correctly installed/aligned. To ensure
good results and the proper antenna configuration, refer to qualified
professionals.
4.1 Activation ofthe receiver inthe digital terrestrialTV operator‘s network
IMPORTANT Your receiver comes pre-activated to view most of the encoded
digital terrestrial channels broadcast by the operator on a free basis
to subscribers. However, watching some channels may require fee. To
gain access to paid channels, you should contact Customer Support.
Information required to contact the Customer Support are in the
additional instructions that came with the documentation supplied
with the receiver.
After the first turn the receiver will automatically receive additional
information from the digital broadcasts. The process of obtaining the
data may take several minutes, during which the receiver will display a
message that there is no right to watch a channel. At this time, do not
change channels. Wait for the image of the transmitted channel.
5.0 DAILY OPERATIONS
In this section of the manual sets out the most frequently used functions the receiver.
5.1 Switching on and off the receiver
To switch your receiver ON and OFF, use the button marked with q. This button is located on the remote
control and front panel of the receiver.
Press on this button to switch the receiver into standby mode that consumes no more than 1.00 watts of
power. Press the button again to turn receiver to operating mode.
If you plan not to use the receiver for a long time, unplug it from the mains by unplugging the power
adaptor from the outlet.
5.2 Changing channels
5.2.1 Switch channels in the view mode
For the sequential switching of channels in the view mode you can use buttons pq or PG+ / PG. For
direct switching to a channel with a certain number you can dial the channel number using buttons 09.
5.2.2 Switch channels through the channel list
To switch between the channels through the channel list, do the following:
In view mode, press OK - on the TV screen will be displayed a list of channels.
Using the button pq select from the list a channel you are interested to watch and press OK -
channel list will disappear from the screen and the receiver will show the chosen channel.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 8502 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 8502 in the language / languages: English as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info