480574
21
Zoom out
Zoom in
Previous page
1/27
Next page
PART 1 • English
18
WARNING: A factory reset will permanently delete all your personal settings, timers and stored
channels. Please consider this before you perform a factory reset.
Information
Shows model, software and hardware information.
Recall List
Enable or disable the Recall list function, which supports multi-recall-channel switching. If the status is
set ON then a list of all previously selected channels will be displayed for new selection by pressing the
RECALL button. If the status is set OFF then the receiver will switch to the previously selected channel by
pressing the RECALL button.
Software update
Select Software Update in the main menu and press OK or u to select. There are two software update
options available:
SW update by OTA
The OTA (Over the Air) function allows you to search for software updates available on satellite. Please
ask your local STRONG dealer or visit our website http://www.strong.tv for more information.
In the OTA menu all necessary STRONG OTA settings (Satellite, Frequency, Symbol rate and Polarization)
are already set per default but could also be changed manually. Press OK to initiate the update process.
An attention banner will now be displayed. Press OK to start the update (or EXIT to cancel it). Follow
the instructions displayed on screen. The software searching and update process could take up to 20
minutes depending on the data volume in stream. After the update process has been completed (also if
no update was found) the receiver will reboot and start with the last shown channel.
WARNING: NEVER power off the receiver or pull the mains plug during the software upgrade
process. Doing so might cause irreparable damage to your receiver and will void
your warranty.
SW update by USB
Download the required update file for your receiver model from the support page on our website
http://www.strong.tv or contact your local dealer.
Unzip the file on your computer, if necessary, and copy it to root folder of your USB storage device.
Connect the USB storage device to the USB port of the receiver. Press MENU and select Software Update
By USB. Press OK to enter the software file list. Select the file containing the software image and press
OK to initiate the software update. An attention banner will now be displayed. Press OK to start the
update (or EXIT to cancel it). Follow the instructions displayed on screen. The update process will take
some time. After the update process has been completed the receiver will display “Software Upgrade
Complete. Please Restart”. Unplug the receiver from the mains and plug it in again. Your updated
receiver will start with the last shown channel.
WARNING: NEVER power off the receiver or remove the USB device during the software update
process. Doing so might cause irreparable damage to your receiver and will void
your warranty.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7002 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info