480574
16
Zoom out
Zoom in
Previous page
1/27
Next page
English
PART 1 • English
13
Video Output
This setting is only relevant when the receiver is connected to the TV set via Scart. Select RGB for the
best picture quality or CVBS if your TV doesn’t support RGB.
Loop Through (VCR to TV Scart)
This option is only relevant if you have a device (video-/DVD-recorder) connected to the VCR scart
connector of your receiver. Its signal will be looped through to the TV scart output of your receiver. Use
this option to set the preferred loop-through mode.
Running mode: The Loop through will be switched off when the receiver is in the
standby mode.
Always: The Loop through is always on – in operation and in the standby mode.
By pressing the DTV/VCR button on the remote control you can switch between DTV/VCR contents in
operation mode. “AV IN” will be displayed on the front LED display when the receiver is in VCR mode.
Press the DTV/VCR button again to return to the digital TV content.
NOTE: The setting "Always" increases the power consumption in standby mode. The front
panel LED remains green in standby!
7.3 Channel Search
To access the menu press MENU and select Channel Search. It contains two options: Installation and DB
(Data Base) Management. Select an option and press OK to enter it. Press EXIT to exit the menu.
7.3.1 Installation
7.3.1.1 Satellite Selection
Use the pq buttons to highlight the satellite your dish is aimed at. Its antenna settings will be shown at
the right side. You can enter the right side with the tu buttons and return to the satellite list with EXIT.
7.3.1.2 Configure the antenna settings for the selected satellite
LNB Type: Press tu or OK to show the list of LNB Types which is shown as frequencies.
You also can enter customized frequencies by User Single or User Dual at the
bottom of the list. The default setting Universal LNB (09750/10600) – the most
used on the market.
LNB Power: Use tu to set the LNB power. 13/18V is the setting for a Universal LNB.
22KHz: Use tu to switch the 22KHz oscillator signal on or off. Auto is the setting for a
Universal LNB.
Toneburst: To enable or disable the toneburst switcher if available.
DiSEqC1.0: To select the right port from up to 4 (if available) for the right LNB.
DiSEqC1.1: To select the right port from up to 16 (if available) for the right LNB.
Motor: If using a motor, press tu to choose between DiSEqC1.2 and GOTOX
depending on the motor type you use. Then press OK to show the menu for
setting the position or GREEN for location.
DiSEqC1.2: Move the motor to the right position for locking the signal like explained below.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7002 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info