480531
15
Zoom out
Zoom in
Previous page
1/25
Next page
12
PART 1 • English
7.3 Channel Search
To access the menu press MENU and select Channel Search. It contains two options: Installation and DB
(Data Base) Management. Select an option and press OK to enter it. Press EXIT to exit the menu.
7.3.1 Installation
7.3.1.1 Satellite Selection
Use pqbuttons to highlight the satellite your dish is aimed at. Its antenna settings will be shown at the
right side. You can enter the right side with tu buttons and return to the satellite list with EXIT.
7.3.1.2 Configure the antenna settings for selected satellite
LNB Type: Press tu or OK to show the list of LNB Types which is shown as frequencies
of local oscillator. You also can enter frequency by User Single, User Dual at
bottom of the list. Default is set a Universal LNB (09750/10600) – the most
used on the market.
LNB Power: Press tu to set the LNB power. 13/18V is the setting for a Universal LNB.
22 kHz: Press tu to switch on or off the 22KHz oscillator signal. Auto is the setting for
a Universal LNB.
Toneburst: to enable or disable the toneburst switcher if available.
DiSEqC1.0: to select the right port from up to 4 (if available) for the right LNB.
DiSEqC1.1: to select the right port from up to 16 (if available) for the right LNB.
Motor: if using a motor press tu to select between DiSEqC1.2 or GOTOX depending
of motor type. Then Press OK to show the menu to set position or GREEN
for location.
DiSEqC1.2: Move the motor to the right position for locking the signal like explained below.
Move Continue: Press tu for moving West / East. It will keep moving as long as the button is
hold pressed. Once pressing will move in 1°step.
Move Step(1): Press tu for moving West / East in 0.3° step.
Store Position: to store the current motor position for selected satellite.
Goto Reference: to go to the reference 0° position.
GOTO X: Set your location coordinates. Main German locations are preinstalled. Press
tu to select. If Manual selected use tu, UP/DOWN and NUMERIC buttons
to enter the right position. By pressing OK position gets stored and the motor
moves automatically towards selected satellite.
Set Limit for DiSEqC1.2 and GOTO X options:
For Move Continue, Move Step(1) and Goto Reference please see explanation above.
Set West Limit: to store the current motor position as West limit.
Set East Limit: to store the current motor position as East limit.
Disable Limit: to disable West and East limits
7.3.1.3 Channel Scan
Automatic Scan
Single Satellite Scan: Press BLUE for Scan. A window with scanning settings will be displayed.
Scan Mode: Press tu to select Default, Blind Scan or NetWork.
Default: All in the memory stored transponders will be scanned.
Blind Scan: Slow scan in 2 MHz step. It first scans the whole frequency band to get the
transponders which can be locked. After gathering all transponders, it scans
the transponders one by one to get the programs.
NetWork: Network search will be performed – when a Network information is
broadcasted new switched transponders will be found and stored.
Crypted: Press tu to select All Channels (scrambled and free) or FTA Channels (free to air);
Service Type: Press tu to select ALL, DTV or Radio.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7000 in the language / languages: English as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info