480531
23
Zoom out
Zoom in
Previous page
1/25
Next page
20
PART 1 • English
8.0 TROUBLESHOOTING
There may be various reasons for abnormal operation of the receiver. Please check the receiver according
to the procedures shown below. If the receiver does not work properly after checking it, please contact
your local Serviceline or STRONG dealer. Alternatively you can send a support mail via our website: www.
strong.tv. NEVER open or disassemble your receiver. This may cause a dangerous situation and will void
the warranty.
PROBLEM
POSSIBLE CAUSE WHAT TO DO
Stand-by indicator
does not light up
Mains lead unplugged /
multipoint connector switched off.
Check mains lead / switch multipoint
connector on.
Front panel switch is in
OFF position.
Set front panel switch to ON position.
No picture The receiver can’t receive
the signal.
Check the antenna cable, replace the cable, or
connect the cable to the receiver tightly.
Incorrect values of some
tuner parameters.
Set the values of tuner parameters correctly
in menu Installation.
Wrong direction of the dish. Check the signal strength with a spectrum
analyzer and adjust your dish correctly.
No picture or
sound on TV
Input is not selected on your TV. Switch to correct TV input.
TV or VCR is not connected
to main.
Bad cable connection.
Check mains lead.
Firmly plug in cables between receiver
and TV.
Audio muting. Press the MUTE button.
TV power off. Turn TV on.
Scrambled channel
message
Channel is scrambled. Select alternative channel.
No response to
remote control
Receiver off. Plug in and turn on plug.
Handset not aimed correctly. Aim handset at IR sensor.
IR sensor obstructed. Check for obstructions.
Hand set batteries exhausted. Replace handset batteries.
Password forgotten Contact local Service Hotline or send email to
our Support via www.strong.tv
The external
USB HDD does
not start.
Power consumption is too high. Connect an extra power supply adapter to
your USB HDD device.
Record
not performed
The USB storage device is
not connected.
Make sure a storage device is connected.
There is no free space on the
storage device.
Delete some data from the storage device
and try again.
The USB storage device format is
not supported.
Make sure your USB storage device is
formatted in FAT or FAT32 file system. Refer
to 7.7.4 Recording Configure>Format.
The receiver
switches to
STBY automatically.
Auto Standby function is activated
and reached the adjusted time
(default 3h).
In the menu System>Auto Standby you
can adjust the Auto Power Down time or
disable it.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7000 in the language / languages: English as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info