480531
9
Zoom out
Zoom in
Previous page
1/25
Next page
6
PART 1 • English
4.0 FIRST TIME INSTALLATION
After all connections have been made properly, switch on TV and make sure the receiver is connected
to the main power. Then switch on the receiver. If you are using the receiver for the first time or restored
to factory default, the First Installation menu will appear on your TV screen. Use tu buttons to select
the OSD Language of your preference and press OK to confirm. An Info page will be displayed. Read the
guide info and press the INFO button to proceed to the next Installation step. You can open and close the
info page again by using the INFO button.
NOTE: If German is confirmed as language, German preset channels from ASTRA 19.2E will
be installed. You can continue with the Installation menu to scan and install further
channels like described below or quit it by double pressing the EXIT button and enjoy
the pre-installed channels.
4.1 Installation
Satellite Selection
use pq to highlight the satellite your dish is aimed at. When using a multi feed antenna with more than
1 LNB, select the satellites your antenna is adjusted for by OK button and set the appropriate LNB´s in
the DiSEqC point. The scan process will be done then on all selected satellites.
Signal Adjust
the signal quality bar on the bottom of the screen allows you to fine tune the alignment of your antenna
for optimum reception. Adjust your antenna for maximum possible signal quality. Once the signal cannot
be improved anymore, fix the dish on this position and press the BLUE button for Scan.
Scan Mode
use pqtu to highlight the desired options and press OK to start the Channel Search. Default settings
are recommended.
Channel Search
your receiver will now perform an automatic channel search. Once the process is finished, all found
channels will be stored and the receiver will switch to the first found channel. You are now ready to enjoy
your new receiver.
NOTE: If no channels were found during the automatic channel scan, the receiver will return to
the First Installation menu. Please select your language again and refer to chapter 7.3.
for further instructions.
5.0 QUICK GUIDE TO USING YOUR RECEIVER
We at STRONG understand that you can’t wait to enjoy your new HD receiver. The following quick guide
will make you familiar with the basic operation of this device. We do, however, advice you to read the full
manual to get the best performance from your STRONG HD receiver.
To turn your receiver ON or to Standby, use the STANDBY button on the remote control or the button on
the left side of the front panel.
Choose the desired channel with the pq buttons. Alternatively, you can digit the channel number with
the 0~9 buttons on the remote control. Or press OK in viewing mode to display the channel list.
The volume can be adjusted with the tu buttons.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7000 in the language / languages: English as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info