480531
8
Zoom out
Zoom in
Previous page
1/25
Next page
5
PART 1 • English
English
25. u /PLAY Starts/resumes the playback.
26. 2 /PAUSE Starts/resumes timeshift when USB device is connected. Freezes/
resumes the playback of Multimedia files.
27. 3 /STOP Stops playback/timeshift/record
28. REPEAT Selects different repeat modes during playback
29. RED Flexible functions in OSD MENU and Teletext
30. GREEN In viewing mode changes resolution of HDMI output between 1080i,
720p, 576p and 576i; flexible functions in OSD MENU and Teletext.
31. YELLOW In viewing mode changes aspect ratio and aspect conversion of Video
outputs; flexible functions in OSD MENU and Teletext.
32. BLUE In viewing mode displays Schedule menu for easy setup timers; flexible
functions in OSD MENU and Teletext.
2.5 Installing the Batteries
Remove the battery cover from the remote control and put 2xAAA size batteries inside the compartment.
The diagram inside the battery compartment shows the correct way to install the batteries.
1. Open the cover 2. Install batteries 3. Close the cover
Fig. 4
NOTE: The batteries should not be recharged, disassembled, electrically short-circuited, be
mixed or used with other types of batteries.
2.6 Using the Remote Control
Fig. 5
To use the remote control, point it towards the front of the digital receiver. The remote control has a
range of up to 7 metres from the receiver in an appropriate angle.
The remote control will not operate if its path is blocked.
NOTE: Sunlight or very bright light will decrease the sensitivity of the remote control.
3.0 CONNECTIONS
3.1 Basic connection using a Scart cable
Fig. 6
1. Connect the LNB of your satellite antenna to the SAT IN connector of your receiver using a
good quality coax cable and suitable ‘F-connector’ plugs.
2. Connect one end of a good quality Scart cable to the TV SCART connector on your receiver
and the other end to the SCART input of your TV.
3. Plug the power cord to a suitable wall outlet.
3.2 Basic connection using an HDMI cable
Fig. 7
1. Connect the LNB of your satellite antenna to the SAT IN connector of your receiver using a
good quality coax cable and suitable ‘F-connector’ plugs.
2. Connect one end of a good quality HDMI cable to the HDMI output on your receiver and
the other end to the HDMI input of your TV.
3. Plug the power cord to a suitable wall outlet.
3.3 Connecting multiple fixed LNB´s using a DiSEqC 1.0 switch
Fig. 8
1. Connect the LNB’s of your fixed antenna to the inputs of a DiSEqC 1.0 switch
2. Connect the output or “to receiver” connector of the DiSEqC 1.0 switch to the SAT IN
connector on your receiver.
3. Refer to section 3.1 or 3.2 for TV and mains connections.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7000 in the language / languages: English as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info