790823

Strom E-Boiler Manual

34
Zoom out
Zoom in
Previous page
1/44
Next page
www.stromltd.com
STROM LIMITED 2021
34
Electric Boilers
SET PUMP SPEED & PURGE AIR
Before moving the boiler out of standby mode please check and complete the following actions:
1. The boiler has been properly congured in the previous step.
2. The airvent on the pump is open with the dust cap moving freely.
3. Set the pump to pump speed one, this for many installations should be adequate.
The boiler can no be activated, press and hold the power button until the boiler bleeps and exits standby mode.
The rst thing you will notice is the ashing Thermostat Status Symbol, this means that currently there is no
demand from the thermostat for heating.
Activate the thermostat so that it is now calling for heat, the Thermostat Status Symbol should now remain
static and lit. The pump will re up and after a few seconds the ignition symbol should illuminate and heat
should start being produced.
While the pump is running you should begin to purge all air from the system by bleeding all radiators and airvents
in the system. Once bled the system should run almost silently with very little noise coming from the boiler or
pump. One all air is purged you can begin to alter the pump speed to suit your needs, normally a 15 to 20 degree
differential between the ow and return is desireable, and the pump speed can be increased or decreased to
achieve this differential.
You should also now take the time to set the Automatic Bypass Valve on the system, with all TRV’s on the
system open and the pump set at the correct speed set the Autobypass Valve to only just closed, now conrm
you have the correct setting by closing only one of the TRV’s, the bypass valve should now start to allow small
amounts of water to pass.
Finally now that all the air has been purged from the system check the nal pressure reading of the heating circuit,
and top up if required. Once set please disconnect the lling loop or water supply to the water replenishment
valve, and ensure that all connections are capped off until required again at a future date.
… 34 …


Need help? Post your question in this forum.

Forumrules
1

Forum

strom-e-boiler

Reset search

  • After turning off heater, I cannot turn it back on. The Menu button does not work. Submitted on 5-4-2023 at 16:40

    Reply Report abuse

  • the front panel is flashing E5 and I can not change anything Submitted on 13-12-2022 at 13:27

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strom E-Boiler at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strom E-Boiler in the language / languages: English as an attachment in your email.

The manual is 3.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info