790823
33
Zoom out
Zoom in
Previous page
1/44
Next page
33
Electric Boilers
SET THE BOILER PARAMETERS
The boiler has 3 key parameters that need to be set in order to make the boiler function correctly:
CLOCK
The time function displays the Time on the front of the boiler during normal operation, this helps the homeowner
to conrm that the programmer has been programmed correctly by letting them see the time the boiler has
become activated.
BOILER FLOW TEMPERATURE
The boiler ow temperature displays on the boiler as “HEAt”. The default position is 65oC, this should however be
set to the design temperature of the heating system, in many cases on existing properties with standard radiator
systems 65oC will be correct, however underoor heating systems and low temperature radiator systems may
be as low as 35oC. If this is not adjusted on set correctly the boiler may cycle and experience overheating
problems. If a hot water cylinder is present most systems would be remain set at 65oC
BOILER DIFFERENTIAL
The boiler differential temperature displays on the boiler as “dIFF”. When the boiler nally reaches the ow
temperature set on the boiler the heat exchanger will turn off to allow heat to dissipate in the system. It will only
re again when the temperature drops by the number degrees set in this setting. For example if FLOW is set as
65oC and dIFF is set as 15oC when the boiler ow hits 65oC it will not reactivate until 50oC is reached. Default
position for this setting is 15oC.
To change the settings with the boiler still in the standby position press and hold the Menu button (see page
10) untill “CLOCK” begins to ash, using the up and down button press set the time, pressing the menu button
again to move from hours to minutes. If the boiler doesnt enter the admin mode it is likely the boiler is not in the
standby position, press and hold the power button until the boiler enters standby and try again.
Pressing the Menu button again will cause HEAt to be displayed, again using the up and down button set the
heat output to the correct design temperature.
Finally press the Menu button again and dIFF will be displayed, nally using the up and down buttons for the nal
time set the heat differential of the boiler.
Press and hold the power button for a few seconds waiting for the boiler to beep and for the Admin menu to be
exited.
CHANGING THE SETTINGS:
33


Need help? Post your question in this forum.

Forumrules
1

Forum

strom-e-boiler

Reset search

  • After turning off heater, I cannot turn it back on. The Menu button does not work. Submitted on 5-4-2023 at 16:40

    Reply Report abuse
  • the front panel is flashing E5 and I can not change anything Submitted on 13-12-2022 at 13:27

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strom E-Boiler at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strom E-Boiler in the language / languages: English as an attachment in your email.

The manual is 3.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info