537181
23
Zoom out
Zoom in
Previous page
1/192
Next page
ADG 2
English
21
If the switch is in order, the display
changes when the trigger is operated
and the light emitting diode on the
analyzer glows green:
If the display does not change or a value
of 100% is not reached with the control
fully depressed, there is a fault in the
control – refer to troubleshooting
procedure in Technical Information
bulletins on ADG 2 analyzer and the
power tool concerned.
N For further fault display, press the
lower button.
Fault display
If there are no faults in the cordless
power tool ...
The light emitting diode on the analyzer
glows continuously green.
The test is restarted by pressing the
lower button.
If there is no fault in the cordless power
tool ...
Depending on the fault, the light emitting
diode on the analyzer glows
continuously yellow or red:
Red continuous light: Active fault,
cordless power tool not ready for
operation – a damage code is
displayed.
Yellow continuous light: Intermittent
fault in the past (e.g. loose contact),
cordless power tool ready for
operation – the fault can be called
up in the power tool's fault memory.
The two-digit code on the display
(shown as XX in the description)
indicates the cause of the fault in the
cordless power tool. In case of claims,
always quote the code on the warranty
request form.
Always remove the adapter from the
power tool before starting repair.
N Press in both locking tabs (1) at the
same time to unlock the adapter (2).
N Take the adapter (2) out of the
housing.
N Press the lower button to confirm.
The data of the cordless power tool
remains stored in the analyzer for about
30 minutes.
When the adapter is removed, any
active faults and entries in the fault
memory are shown. Scroll between the
displays with the analyzer's
pushbuttons. For repair procedure, see
Technical Information bulletins on
ADG 2 analyzer and the cordless power
tool concerned.
Clearing the fault memory
The fault memory may be cleared after
completing the repair.
N After viewing last entry in fault
memory, press the lower button.
N Press and hold down both buttons
for about 3 seconds.
Operate trigger switch
ON 100%
No fault
End of test
Damage code
XX
Remove adapter
before repair
Clear memory?
Press both buttons
Clear: no
Clear: yes
2
1
7BA004 KN
1
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl ADG 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl ADG 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info