537181
22
Zoom out
Zoom in
Previous page
1/192
Next page
ADG 2
English
20
N Push the battery (1) into the
analyzer (2) until you feel noticeable
resistance – then push it as far as
stop.
The test continues automatically when
the battery is inserted. If the test does
not continue, the reason may be:
No contact between battery and
analyzer – remove the battery and
refit it.
Fault in battery – test with STIHL
ADG 1 battery analyzer if
necessary.
If the battery's state of charge is too low,
the analyzer's display shows:
N Use a properly charged battery.
Insert adapter
Inserting the adapter connects the
cordless power tool to the battery. The
cordless power tool is ready for
operation.
WARNING
The cordless power tool's motor starts to
run during the test. Before starting the
test, always take precautions to
eliminate the risk of accidents and injury
from contact with the power tool's
attachment.
The following instructions appear on the
display:
N Eliminate risk from tool – see
Technical Information bulletins on
ADG 2 analyzer and the cordless
power tool being tested.
N Press the lower button to confirm.
N Insert adapter (1) in power tool's
battery compartment – the adapter
slides into position – press it home
until it engages audibly. The
adapter must be flush with the top of
the housing.
N Press the lower button to confirm.
N Press the lower button to confirm.
Data transfer
The cordless power tool and analyzer
communicate with each other. The
analyzer can test the cordless power
tool only if this data exchange functions.
N Switch on the cordless power tool
see power tool's instruction manual.
If there is no data exchange between the
power tool and the analyzer, the
problem is in the connection to the
power tool – refer to Technical
Information bulletins on ADG 2 analyzer
and the power tool concerned.
N Switch on the cordless power tool
again – the test starts.
Checking operation of controls
The controls differ according to the
cordless power tool being tested. The
following procedure describes the
trigger switch on the FSA 85 cordless
trimmer as an example.
The display always shows the current
position of the control:
N Operate trigger switch
State of charge too low
2
7BA002 KN
Eliminate risk from
tool
Insert adapter
CAUTION!
Motor may start
1
7BA003 KN
Switch on the saw.
Data transfer
Switch on unit again
Operate trigger switch
OFF 0%
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl ADG 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl ADG 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info