Manual Stiga TORNADO 2198 H (page 62 of 112) (English, German, Dutch, French, Italian)

608471

Zoom out

Zoom in

1/112

Fit the dashboard cover (4) clicking the seven

fasteners into place.

Fit the steering wheel (5) onto the hub (1) with

the spokes pointing in the proper direction.

3.3 FITTING THE SEAT (Fig. 3.3)

Fit the seat (1) onto the plate (2) using the

screws (3).

3.4 ASSEMBLY AND CONNECTING

HE BATTERY (Fig. 3.4)

The battery (1) is housed under the seat and

secured by a spring (2).

First connect the red wire (3) to the positive pole

(+) and then the black wire (4) to the negative

pole (–), using the screws supplied as shown.

Apply silicone grease to the terminals and

check that the protective cap for the red wire (5)

is in place.

IMPORTANT Always fully charge the bat-

tery according to the instructions in the battery

booklet.

IMPORTANT To prevent the safety device in

the electronic circuit board from cutting in, never

start the engine until the battery is fully charged!

3.5 MOUNTING THE FRONT BUMPER

(if provided)

• Bumper Type “I” (Fig. 3.5)

Mount the front bumper (1) on the bottom of the

frame (2) using the four screws (3).

• Bumper Type “Il” (Fig. 3.6)

Fit the two brackets (1) and (2) to the bottom of

the frame (3) and fully tighten the screws (4).

Attach the front bumper (5) to the brackets (1)

and (2) using the screws (6) and nuts (7).

3.6 FITTING THE SIDE DISCHARGE

CHUTE (Fig. 3.7)

From the inside of the side discharge chute

(1), t the spring (2) by inserting the terminal

(2a) into the hole and turning it so that both the

spring (2) and the terminal (2a) are securely po-

sitioned in their seatings.

Position the side discharge chute (1) in line

with the cutting-means assembly brackets (3).

Using a screwdriver, turn the second terminal

(2b) of the spring (2) to bring it outside the side

discharge chute.

Fit the pin (4) in the holes on the brackets (3)

and on the side discharge chute, so that it

passes through the coils of the spring (2) and

the drilled end comes out of the inner most

bracket.

Insert the cotter pin (5) in the pin (4) hole (4a)

and rotate the pin until it is possible to bend the

two ends (5a) of the cotter pin, (with the aid of a

pair of pliers), so it cannot slide out and cause

the pin to fall out (4).

WARNING! Check that the spring works

correctly and keep the side discharge chute

securely lowered. Make sure that the pin is

fitted properly to prevent it from falling out

accidentally.

3.7 REPOSITIONING THE ANTI-CHIPPING

WHEELS (Fig. 3.8)

For transport reasons, the anti-chipping wheels

(1) are fastened on the top hole.

In order for them to work properly, the anti-

chipping wheels (1) must be repositioned in the

hole which is most suited for the type of ground

(see 5.4.5) .

4. CONTROLS AND INSTRUMENTS

4.1 STEERING WHEEL (Fig. 4.1 no.1)

Turns the front wheels.

4.2 THROTTLE LEVER (Fig. 4.1 no.2)

Regulates the engine’s r.p.m. The positions are

indicated on the plate showing the following

symbols:

«CHOKE» cold start

«SLOW» for minimum engine speed

«FAST» for maximum engine speed

– The «CHOKE» position enriches the mixture

so it must only be used for the time necessary

for cold starts.

– When moving from one area to another, put

the lever in a position between «SLOW» and

«FAST».

– When cutting, shift into «FAST”.

4.2a CHOKE CONTROL (if tted)

(Fig. 4.1 no.2a)

It enriches the mixture and must only be used

for the necessary time for cold starts.

How do you set it for mulching mode. I have no manual. It leaves a row of grass between blades at moment. Thanks. Submitted on 23-3-2018 at 03:58
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga TORNADO 2198 H in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga TORNADO 2198 H Manual

Product: