- Check if the gearbox control lever (Fig.8 part.4 only 2+2 speed version) is on loose position.
- Adjust the handlebar to the requested position/height:
Open the fuel cap (for the engine equipped like this), push to halway the accelerator lever on the handlebar
(part.1) if the engine is cold, operate the starte device on the carburettor, bring the starter handle and pull energetically.
When the engine is on , after some bursts/bangs, put the starter again at rest position,
- Grasp the handlebar, insert the speed (for 2+2 speed version) pos.A slow speed, pos. B fast speed. At the beginning we recommend you to
work on position 1, slow speed.
- grasp the handlebars (8) lift the prevention lever (9) and then pull the forwarding lever (2) all its way.
- (part.2) and pull towards ourselves the lever (3) on the handlebar, to lift up the back part of
the machine in order to make the rotavator to come out from the ground until the machines starts to draw back.
- At the end of the work: when you nish the work, to stop the engine, bring the accelerator lever (1 Fig.8) to the bottom gear or press the stop
switcher on the engine.
GARAGING AND SCHEDULED MAINTENANCE
Keep attention that all the nuts ,screws and bolts are tightened in order to guarantee a good machine working on safety conditions. Leave the machine
to cool before garaging anyhow don’t room it if the tank still contains some fuel as the vapours could reach some blazes or sparks. To lower the re
danger, keep the engine , the silencer and the fuel area free from leaves, grass or greasy substances.
Perform the following operations as per the described intervals. (with the word "Hours", we mean the machine working hours).
Gearbox Use oil SAE 80. Verify the oil level every 60 hours: put the machine on at surface, remove the cap 1 and
check if the oil reaches the hole bottom edge. In case you need to ll it on you have to perform it from the hole of the cap 2. Go on with such operation
until you see the oil coming out from control cap 1. Screw both caps again.
Oil change: change the oil every 150 hours. The oil drain has to be performed when the machine is hot: remove caps 1, and 2 and tilt the machine
to a complete emptying , then put the machine on at land, ll it in with oil through the hole of cap 2 until the oil starts coming out from control cap
1. Screw both caps again.
ATTENTION ! Waste fuel oil is a polluting material: don’t waste it in the sorroundings, please apply to suitable waste material centres.
Cultivator Every time the motorcultivator is used, it is necessary that the operator controls if the screws ad the xing nuts of the spades
on the shaft are tightened all the way home (part.3 and 9).
Reverse speed shaftEvery 50 working hours, grease the reverse speed shaft with the suitable greaser (1), upon disassembling of
rubber cap (1). KEEP ATTENTION! once such
NOISE LEVEL AND VIBRATION LEVEL Measured sound power level LWA = 89,1 dB (A), with a uncertainty value K = ±1,2 dB (A).
Measured sound pressure level with En709, Leq = 80 dB (A), with a uncertainty value K = ±1,1 dB (A). Handlebar vibration in compliance with EN
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Stiga SILEX 103 B at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Stiga SILEX 103 B in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.
The manual is 1,74 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
