Assembly of the hinge engine hood rotary cutterput the hinge hooks (part. 1) keeping it turning to the top side into the slots
on the engine hood milling, lower the hinge and screw down the plates (2) with the relevant screws (3). ATTENTION ! The strap should be placed
with the hooks placed as shown in the picture specs. This is to say that the hooks should enter from top to down into the hole “B” and come our from
“A” position.
ADJUSTMENTS
Adjustment of the belt stretcher driving wire single speed and reversethe wheels have to start working
only when the control lever has moved halfway its travel. When the lever is completely pulled (working position), the spring load of the belt stretcher
(part. 1 single speed) and (part.2 reverse speed) must extend for 6-8 mm. In order to obtain he a.m. conditions you have to act on the regulator
(3) you can see near the drive control lever. The transmission reverse REV. (4) the lever on position released should have some clearance on the
registers. Please, carefully check from time to time the adjustement of the two transmissions in order to avoid the belts sliding and the
consequent pulleys overheating.
Adjustment of the handlebar positionThe handlebar position can be height adjusted. Before starting any work it is a good standard
operating procedure to adjust the handlebar to the operator’s requirements so that the machine could be easily handled. The particular shape of of
the single speed control lever allows the operator to drive the machine from the right or the left side in order not to thread on the cultivated ground nor
to squash the vegetation. Unscrew down the handlebar support screws (part. 1). Adjust to the suitable/requested position, block the screws (1).
Depht adjustmentIn order to obtain a good soil cultivation and a smooth machine movement , the cultivators is equipped with a depth
setting device (part.2) which regulates the spade working depth. When the depth control lever is pulled is pulled back (1) and moving the same up
or down, you can regulated spade penetration into the soil: the adjustment is correct when the machine when the machine moves forward smoothly
without lifting out or digging into the soil.
- Hard soils cultivation: bring the depth to position (B). such postion corresponds to a small soil penetration.
- Soft soils penetration: Bring the depth to position (A). suc position corresponds to a deept soil penetration depth.
When moving with the machine working on different surfaces, keep the depth on position (B) in order to avoid the spades to break up the top
of the surface.
CONTROLS DESCRIPTION 1) Accelerator lever control Start-Stop 2) Forward speed lever control. 3) Forward speed lever control
4) Control speed SLOW-FAST (2+2 speed version only) 5) “Fork on 3 positions” 6) Starter handle 7) Root face control lever.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Stiga SILEX 103 B at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Stiga SILEX 103 B in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.
The manual is 1,74 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
