608686
10
Zoom out
Zoom in
Previous page
1/18
Next page
62
ENGLISH
EN
2.4.9 Ignition lock (4,5:I)
Ignition lock used for starting/stopping the engine.
There are 3 positions:
1. Stop position – the engine is short-cir-
cuited. The key can be removed.
2. Operating position
3. Start position – the electric start motor
is activated when the key is turned to the
spring-loaded start position. Once the en-
gine has started, let the key return to oper-
ating position 2.
NOTE! If the engine should stop for any reason,
the key cannot be turned directly to position 3
due to a mechanical ignition lock. To start the
engine - turn the key back to position 1 and then
to positions 2 and 3.
2.4.10 Power take-off (4:K) (4WD)
Switch for engaging/disengaging the electromag-
netic power take-off for operating front-mounted
accessories. Two positions:
1. Press the front part of the switch – the
power take-off is engaged. The symbol
will light up.
2. Press the rear part of the switch – the
power take-off is disengaged.
2.4.11 Power take-off (4,5:K)
A lever for engaging and disengaging the power
take-off for operating front-mounted accessories.
Two positions:
1. Lever in forward position – power take-
off disengaged.
2. Lever in backward position - power
take-off engaged.
2.4.12 Hour meter (2:P)
Indicates the number of working hours. Only
works when the engine is running.
2.4.13 Cruise control (4:N) (4WD)
A switch for activating the cruise control. The
cruise control locks the pedal (3:F) in the desired
position.
1. Press down the pedal (3:F) until the de-
sired speed is obtained. Then press the
front part of the switch to activate the
cruise control. The symbol will light up.
2. Disengage the cruise control by releas-
ing it with the pedal (3:B) or pressing the
rear part of the switch.
2.4.14 Cutting height adjustment (4,5:J)
The machine is equipped with a control for using
the cutting deck with electrical cutting height ad-
justment.
The switch is used to adjust the cutting
height in continuously variable positions.
The cutting deck is connected to the contact (2:Q).
2.4.15Rear Rake (4:L) (4WD)
The machine is fitted with a control for electrical
adjustment of a rear rake (available as an
accessory).
The switch is used to raise and lower the
rear rake.
Cables for connecting the rear rake are found at the
rear of the machine, to the left of the upper side of
the bumper. (4WD is prepared for a rear rake,
cables routed).
2.4.16 Sand spreader (4:O)
(4WD)
The machine has been designed for electrical ad-
justment of a sand spreader (accessory).
The switch is used to start and stop the
spreader.
Cables for connecting the sand spreader are at the
rear of the machine.
2.4.17Clutch release lever
A lever for disengaging the variable transmission.
2WD is equipped with a lever, connected to the
rear axle. See (6:R).
4WD is equipped with two levers, connected to the
rear axle (7:A) and the front axle (7:B).
The disengagement lever must never be
between the outer and inner positions.
This overheats and damages the trans-
mission.
The levers enable the machine to be moved by
hand without the help of the engine. Two positions:
1. Lever in the inner position –
transmission engaged for normal
operation.
2. Lever in the outer position –
transmission disengaged. The
machine can be moved by hand.
The machine may not be towed over long distances
or at high speeds. The transmission could be dam-
aged.
The machine must not be operated with
the forward most lever in the outer po-
sition. Risk of damage and oil leakage in
the front axle.
12V
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga PARK DIESEL 4WD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga PARK DIESEL 4WD in the language / languages: English as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info