593151
9
Zoom out
Zoom in
Previous page
1/48
Next page
Dimensions: (H x W x D) 113 x 78 x 73 mm
Output: 600 watts max . (resistive load, e.g. fi lament bulb)
500 watts max. (uncorrected, inductive,
cos φ = 0.5, e.g. fl uorescent tubes)
500 watts max. (series corrected)
500 watts max. (shunt corrected, at C ≤ 45.6 µF)
Electronic ballasts, capacitive
e.g. low-energy lamps,
6 each max., C ≤ 132 µF
Connection: 230 – 240 V, 50 Hz
terminal block suitable for following supply leads:
3-core Ø 1.5 or 2.5 mm
2
or 5-core Ø 1.5 mm
2
Angle of coverage: 160° with sneak-by guard
Pivoting range: 40° horizontal, 70° vertical
Reach: 12 m max.
Light threshold: 2 – 2000 lux
Time setting: 8 sec. – 35 min. (factory setting: 10 sec.)
Light threshold: 2 – 2000 lux (factory setting: 2000 lux)
Enclosure: IP 54
Temperature range: -20 °C to +50 °C
Technical specifi cations
Without power
W
Fuse blown, not
switched ‘ON’
W
Short circuit
W
Renew fuse, switch
‘ON’ mains power
switch, check wiring
with voltage tester
W
Check connections
Does not switch ‘ON’
W
Twilight setting in
nighttime mode during
daytime operation
W
Bulb blown
W
Mains switch ‘OFF’
W
Fuse blown
W
Detection zone not
properly targeted
W
Readjust
W
Replace bulb
W
Switch ‘ON’
W
Renew fuse, check
connection if
necessary
W
Re-adjust
Troubleshooting
Malfunction
Cause
Remedy
16
17
Remedy
Does not switch ‘OFF’
W
Continued movement
in detection zone
W
Light is in detection
zone and keeps switch-
ing on as a result of
temperature change
W
Set to continuous ope-
ration by indoor series
switch
W
Check detection zone
and re-adjust if neces-
sary or fi t shrouds
W
Readjust zone
W
Set series switch to
automatic mode
Keeps switchingON’/’OFF’
W
Light is in detection
zone
W
Animals moving in
detection zone
W
Change zone, increase
distance,
reduce output
W
Tilt sensor higher or
apply specifi c shrouds,
adjust detection zone
or fi t shrouds
Switches ‘ON’ when it
should not
W
Wind is moving trees
and bushes in the de-
tection zone
W
Cars in the street are
being detected
W
Sudden temperature
changes due to wea-
ther (wind, rain, snow)
or air expelled from
fans or open windows
W
Adjust detection zone
or fi t shrouds
W
Change detection
zone, tilt sensor down
W
Adjust detection zone
or change site of in-
stallation
Reach modifi cation
W
Change in ambient
temperatures
W
When it is cold,
shorten reach by tilting
sensor down
W
When it is hot, tilt
sensor up
CauseMalfunction
GB
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel IS 2160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel IS 2160 in the language / languages: All languages as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info