593151
8
Zoom out
Zoom in
Previous page
1/48
Next page
14
The system can be put into
operation once the sensor
has been connected and
installed. Two setting con-
Switch-off delay
(time setting)
The chosen light ‘ON’ time
can be varied continuous-
ly from approx. 8 sec. to a
maximum of 35 min. The
shortest period, approx.
8 sec., is selected by
turning the control fully
clockwise. The longest
period, approx. 35 mins.
is selected by turning the
control fully anticlockwise.
It is recommended to
select the shortest time
for adjusting the detection
zone and for performing
the walk test. Any move-
ment in the detection
zone will re-activate the
time setting.
Twilight setting
(response threshold)
The chosen detector
response threshold can
be adjusted continuously
from approx. 2 lux to 2000
lux. Turning the control
fully clockwise will select
daytime operation at ap-
prox. 2000 lux.
Turned fully anti-clock-
wise, the control is set to
dusk-to-dawn operation
at approx. 2 lux. When
adjusting the detection
zone and for the perform-
ance test in daylight, the
adjusting screw must be
turned fully clockwise.
Functions
8 sec. – 35 min.
2 – 2000 lux
trols are provided on the
bottom of the unit.
Reach adjustment
(s. fi g. page 4)
Reach can be reduced by
tilting (70°) the sensor.
The sensor can be turned
horizontally through 40°
(only with swivel mount) to
align the detection zone
in exactly the way you
require.
The adhesive shrouds
provided may be used
to adjust the sensor‘s
detection angle to suit
individual requirements.
This makes it possible,
for example, to blank out
neighbouring premises
from detection or
specifi cally target paths.
Precision adjustment using shrouds
(s. fi g. page 4)
15
pose. Weather conditions
may affect the way the
motion detector works.
Strong gusts of wind,
snow, rain or hail may
cause the light to come
‘on’ when it is not wanted
because the sensor is
unable to distinguish sud-
den changes of tempera-
ture from sources of heat.
The detector lens may be
cleaned with a damp cloth
if it gets dirty (do not use
cleaning agents).
Operation/Maintenance
The Infrared Sensor is
suitable for switching light
‘on’ and ‘off’ automatically.
The unit is not suitable
for special burglary alarm
systems since it lacks
the tampering protection
prescribed for this pur-
1) e.g. 1-4 x 100 W fi lament bulbs
2) Service load, light of 600 W max. (see Technical specifi cations)
3) IS 2160 connection terminals
4) Indoor switch
5) Indoor series switch, manual, automatic
6) Indoor double-throw switch, automatic, permanent light ‘ON’
Wiring examples
2. Light with neutral conductor
1. Light without neutral conductor
4. Connection to double-throw switch
for permanent light ‘ON’ and automatic
operation
Setting I: automatic operation
Setting II: manual operation for permanent
light ‘ON’
Important: the unit cannot be switched
off, but operated only at settings I and II.
3. Connection using series switch
for manual and automatic operation
GB
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel IS 2160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel IS 2160 in the language / languages: All languages as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info