593151
7
Zoom out
Zoom in
Previous page
1/48
Next page
Installation instructions
Dear Customer,
Congratulations on pur-
chasing this STEINEL Inf-
rared Sensor and thank
you for the confi dence
you have shown in us.
You have chosen a high-
quality product that has
been manufactured,
tested and packed with
the greatest care.
Please familiarise yourself
with these instructions
before attempting to in-
stall the sensor since
prolonged reliable and
trouble-free operation will
only be ensured if it is
installed properly.
We hope your new Infra-
red Sensor will give you
lasting satisfaction.
W
Disconnect the power
before attempting any
work on the motion
detector.
W
The electrical connec-
tion lead must be dead
during installation.
Therefore, switch off
the power fi rst and
use a voltage tester to
check that the power
supply is disconnected.
W
Installation of the
sensor involves work
on the mains power
supply. This work must
therefore be carried
out professionally in
accordance with the
applicable wiring regu-
lations and electrical
operating conditions.
(
D - VDE 0100,
A - ÖVE-EN 1,
- SEV 1000).
W
Please note that the
sensor must be pro-
tected by a 10 A circuit
breaker. The mains
supply lead must be
no greater than 10 mm
in diam-eter.
Safety warnings
12
Principle
The integrated pyroelec-
tric infrared detector
senses the invisible heat
radiated from moving
objects (people, animals,
etc.). The heat detected is
electronically converted
into a signal that switches
on loads (e.g. a light) con-
nected to it. Heat is not
detected through obsta-
cles, such as walls or
panes of glass. Heat ra-
diation of this type will,
therefore, not trigger the
sensor.
With a detection angle of
160° and a max. reach of
12 m the sensor watches
over an area of approx.
165 m
2
. If you only wish
to cover a smaller area,
reach may be reduced
by tilting the sensor unit.
Using the swivel mount
supplied, the sensor
unit can also be turned
horizontally, making it
possible to target the
detection zone exactly
as you choose. The
detection angle can also
be adjusted to suit individual
requirements by fi tting
shrouds.
Important: the safest mo-
tion detection is obtained
when the device is moun-
ted and aligned laterally to
the walking direction and
no obstacles (such as
trees and walls, for ex-
ample) obstruct the view.
(s. fi g. page 2)
Installation
(s. fi g. page 3)
The site of installation
should be at least 50 cm
from a light because heat
radiated from it may trig-
ger the sensor uninten-
tionally. To obtain the spe-
cifi ed reach of 12 m, the
sensor should be installed
at a height of approx. 2 m.
Please ob-serve the safe-
ty warnings on page 12.
Installation procedure:
1. Undo screws on hous-
ing 1 2. Do not detach
wir-ing from terminal
block, but gently pull
entire terminal assembly,
including sensor unit 2
(cylindrical section), to
remove it.
3. Hold mounting plate 3
against wall/ceiling, mark
drill holes, paying atten-
tion to wiring runs con-
cealed in wall/ceiling. Drill
holes, insert wall plugs
(6 mm). 4. Break open
pre-punched cable entry
holes as appropriate for
concealed 4 or surface-
mounted 5 installation,
insert grommets, pierce
and pass cable through.
Note: For surface-mount-
ed wiring, it is recommen-
ded to install the swivel
mount 6 (see below).
Alternatively, the unit may
be pierced at the thinner
section to pass the cable
through. 5. Screw mount-
ing plate 3 to wall.
6a) Connecting the
mains lead
The mains lead consists of
a 2-3 phase cable
L = phase conductor
N = neutral conductor
PE = protective-earth
conductor
If you are in any doubt,
you must identify the
cables using a voltage te-
ster; then disconnect the
power supply again.
The phase (L) and neutral
conductor (N) are connec-
ted according to terminal
assignment. The protecti-
ve-earth conduct-or is
connected to the earth
terminal .
A mains switch for ‘ON’
and ‘OFF’ switching can
of course be installed in
the mains lead.
6b) Connecting the load
supply lead
The load supply lead (e.g.
light) is also a 2 to 3-core
cable which is connected
to terminals N and L. The
live conductor must be
connected to the terminal
marked L.
Connect the neutral con-
ductor to the terminal
marked N together with
the neutral conductor of
the mains power supply
lead. The protective-earth
conductor is connected to
the earth terminal .
7. Once wiring is complet-
ed, insert terminal block
together with sensor unit
2 into mounting plate 3,
t housing cover 1 and
secure in place with faste-
ning screws.
13
The swivel mount 6 allows
you to turn the motion
detector horizontally. This
provides additional adju-
stment for the detection
zone.
1. Press cupped pieces
7 out of swivel mount 6
provided with sensor unit.
2. Hold swivel mount 6
against wall and mark drill
holes, drill the holes, insert
wall plugs, pass cable
through. Connect as de-
scribed in „Installation“.
3. Pass screws through
Installation with swivel mount
cupped pieces 7 and
secure swivel mount 6 in
such a way that the screw
head is positioned on the
smooth side and the
domed side rests against
the mounting plate 3 (see
diagram).
GB
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel IS 2160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel IS 2160 in the language / languages: All languages as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info