592483
11
Zoom out
Zoom in
Previous page
1/44
Next page
Functions
2
LUX
30
2 - 2000 lux
10 sec. - 30 min.
(only for IR 180 UP and HF 360 UP)
Functions
Adjusting screw left stop
position means: minimum
reach (approx. 1 m / factory
setting).
Adjusting screw right stop
position means: maximum
reach (approx. 8 m).
(only for HF 360 UP)
Reach setting
(sensitivity)
The term reach denotes
the approximately circular
diameter that results as the
detection zone.
1 - 8 m
18
Twilight setting
(Response threshold)
The desired sensor re-
sponse threshold can be
adjusted continuously from
approx. 2 lux to 2000 lux.
Adjusting screw right stop
position means: Daylight
operation approx. 2000 lux
(factory setting). Adjusting
screw left stop position
means: Night-time oper-
ation approx. 2 lux.
Time setting
(Switch-off delay)
The desired duration of illu-
mination of the connected
light can be continuously
adjusted from approx.
10 sec. to max. 30 min.
Adjusting screw left stop
position means: shortest
time approx. 10 sec. (fac-
tory setting)
Adjusting screw right stop
position means: longest
time approx. 30 min.
The timer is restarted by
any motion detected before
this time elapses.
When adjusting the detec-
tion zone and for the per-
formance test in daylight,
the adjusting screw must be
set to the RH stop position.
The shortest time setting is
recommended when adjus-
ting the detection zone and
performing a functional test.
Note: After every off
switching, further motion
detection is interrupted for
approx. 2 seconds. Only
after this time elapses is it
possible for the Sensor
Switch to switch light again.
(only for IR 180 UP and HF 360 UP)
Button for light functions
Permanent light OFF
mode
Press button for 3 sec.
The connected light is
switched off (red LED
flashes).
By briefly pressing the
button again, the Sensor
Switch returns immediately
to sensor mode (red LED
off).
Permanent light mode
Button 1 x ON
The connected light is set to
permanent light for 4 hours
(red LED illuminates). After
this period, the sensor
switch immediately returns
to sensor mode (red LED
off).
Permanent light can be
interrupted before this time
elapses by pressing the
button (red LED off).
Sensor mode
The Sensor Switch basi-
cally operates in sensor
mode. The light is switched
on for the preset time in
response to movement
within the detection zone.
1 x short 1 x 3 sec.Sensor
10 sec. - 30 min. max. 4 hours OFF
19
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel HF 360 UP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel HF 360 UP in the language / languages: All languages as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info