720461
7
Zoom out
Zoom in
Previous page
1/10
Next page
7
ENGLISH
(Original instructions)
Before the cleaning, unplug the charger plug from the
power source. In addition, except the regular cleaning on
your charger, no other maintenance is needed.
Regularly use the soft brush or dry cloth to clean the
ventilation slot of the equipment / tools / charger.
Regularly use a damp cloth to clean the motor housing.
Please do not use any abrasive cleaning agents or
solvent-based cleansing agents.
Regularly open the clamping chuck and tap it gently to
remove any internal dust (after installation).
Replace the carbon brushes (Fig. E)
Lubrication
Regularly replace and check the carbon brushes.
Replace it in time when it is worn to the abrasive
boundary line. Keep the carbon brush clean and make it
freely slide in the brushing range. Two brushes shall be
replaced at the same time.
Use the cross screwdriver to counterclockwise unscrew
the screws, open the bottom cover(8) with a flat
screwdriver to counterclockwise open the brush
cover(9), you can remove the brush(10)as shown in the
figure E, and put the new brush, and then clockwise
fasten the brush cover(9), finally put the bottom cover(8),
and then use the cross screwdriver to tighten it properly.
Open the cap of the lube oil-injection inlet(2), check the
lube oil in the gearbox, if the lube oil is dirty or
insufficient, replace or add the adequate amount of lube
oil provided by the company.
Cleaning
Warning! Once the visible dust build-up is found at and/or
around the ventilating ports, immediately flush the dust and
powder within the host shell with clean dry air. To perform
this procedure, wear the approved safety equipment and
dust mask.
Warning! It is strictly forbidden to clean the non-metallic
parts of the tool with the solvents or other irritant chemicals.
These chemicals may weaken the materials of these
components. Use a cloth moistened with a mild soapy water
to clean it. Do not let any substance permeate into the tool
and.do not immerse any part of the tool into a liquid.
Technical data
Hammer STHR272
Power input W 850
Voltage V 220-240
Frequency Hz 50/60
No-load speed /min 700
Impact rate BPM 3400
Impact energy (EPTA) J 4.1
Modes 2
Max capacity
Concrete mm 26
Steel mm -
Wood mm -
Weight kg 5.1
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHR272 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHR272 in the language / languages: English as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info