720461
5
Zoom out
Zoom in
Previous page
1/10
Next page
5
ENGLISH
(Original instructions)
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc. Even with
the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks can
not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Label on the tool
Electrical safety
Double insulation measures are taken in this power
tool, so no grounding is needed. Please check
whether the voltage of power supplied is consistent
with the voltage on the nameplate or not.
If the wire is damaged, it should be replaced by the
manufacturer or a service center authorized by
STANLEY, to avoid danger.
Part name
The power tool includes some or all of the following parts:
1. Switch
2. Oil-injection inlet cap
3. Modes selector
4. Tool chuck (tool holder)
5. sleeve
6. Side handle
7. Depth stop
8. Botton cover
Assembly
Warning! Before assembly, please ensure that the power
tool is powered off and the power plug of the tool is
unplugged from the power source.
Install the side handle
Warning! When holes are drilled in the concrete, bricks and
other surfaces, please grip the side handle to ensure safe
operation.
The side handle (6) can be rotated to any side, which
can facilitate the use of the power tool in any position.
Rotate the side handle (6) counterclockwise, to unlock
and release the power tool, rotate it to the desired
position.
Rotate the side handle clockwise to tighten it adequately.
Fitting an accessory (Fig. A)
Please clean the drill shank and lubricate the drill bit
before installing it.
Pull back and hold the slide-sleeve(5), and then screw
the drill bit into the chuck, press it internally until it is
fastened, the drilling bit can be automatically locked in
situ. Pull the drill bit outwards to test whether it has been
adequately locked in the correct position or not.
Pull back and hold the drill sleeve(5) clamp, you can
remove the drill bit.
Use
Warning! Please use the power tool under normal load; no
overloading is permitted.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
The label on your tool may include the following symbols:
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHR272 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHR272 in the language / languages: English as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info