720461
6
Zoom out
Zoom in
Previous page
1/10
Next page
6
ENGLISH
(Original instructions)
Warning! Before drilling holes in the wall, floor or ceiling,
please check the positions of the wire and steel tube.
Chipping/Chiseling (Fig. B)
When the cutting / stripping / removing operation is
conducted, please put the operation modes selector (3)
to position , the drilling bit, cold chisel and scaling
chisel etc. should be properly used.
Warning! Do not rotate the knob when the power tool is
rotating under the load, otherwise it will be damaged.
Hammer drilling (Fig. B)
When using the hammer driller to drill holes on the
masonry and concrete surfaces, the operation mode
selector (3) should be set to position .
The drilling bit should be aligned to the drilling position,
and then press the switch button to achieve the best
effect. Keep the power tool be positioned correctly,
prevent it from deviating the hole.
When the fragments plug the borehole or powders,
please do not apply further pressure, and make the tool
rotate in an idling state, then gradually take out the
drilling bit from the hole. Repeat the said steps for
several times, the plugged hole can be clean, and then
resume the normal drilling.
Warning! When the drilling bit begins to break down the
reinforced concrete or hit the steel bar inside the concrete,
the power tool may have dangerous reaction force. Please
always keep balance, stable posture and tightly grip the tool,
to prevent from generating the dangerous reaction force.
When the concrete is chiseled, the distance between the two
points of one chiseling shall not be too much away from the
edge, which shall be about 8cm or so, define the distance
through finding the cracking strength of the concrete.
Overload coupling device
If the drilling bit is clamped or hooked up, the driving force
transmitted to the drill shaft will be cut off. A huge force will
occur, so two hands must tightly grip the power tool when it
is in operation, and ensure that the operator is standing in a
stable and fixed position.
Select the depth of holes to be drilled (Fig. C)
A depth gauge is an easy to use ruler to ensure that the
drilling depth is consistent. Unlock the side handle, adjust
the depth gauge according to the required depth, and then
tighten the side handle.
Unfasten the side handle (6) by turning
counter-clockwise the grip.
Set the depth stop (7) to the desired position. The
maximum depth of the drilled hole shall equal to the
distance between the tip of drilling bit and the front end
of the depth stop.
Tighten the side handle by turning the grip clockwise.
Switch on and off
Warning! Before inserting the plug, please confirm whether
the switch can trigger freely or not, whether it can return to
the original position after releasing.
Press the switch button (1), the power tool can be
started immediately.
Release the button (1), the tool stops rotating.
Accessories
The performance of an electric tool depends on its
accessories. STANLEY accessories are designed according
to high quality standards, to enhance the performance of
electric tool. The use of these accessories can help you
conveniently operate the tool.
Maintenance
The STANLEY cord / cordless appliance / tools are of
sophisticated design, can be used for a long time, and only
little maintenance is needed. To obtain consistent
satisfactory use, proper maintenance and regular cleaning of
the tools are necessary.
Warning! Before performing any maintenance work on the
cord / cordless electric tools, the following points must be
implemented:
Switch off the power of the equipment / tools and pull off
the plug;
If the equipment / tools are equipped with independent
battery pack, please turn off the power and remove the
battery pack from the equipment / tools.
If the equipment / tools are equipped with an integrated
battery, please run out the battery, before turning off its
power.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHR272 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHR272 in the language / languages: English as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info