720738
11
Zoom out
Zoom in
Previous page
1/36
Next page
(Original instructions) ENGLISH
11
- Proceed as for cross cutting
Cutting particle boards
To prevent the cutting edges from cracking when working with
particle boards, the saw blade must be higher than the
workpiece height.
Auxiliary tools stored (Fig. S, T)
Auxiliary tools can be stored on the machine Miter gauge (6)
could be put on hook as Fig S showed. Blade guard (2) and
push stick (19) could be put on hook as Fig T showed.
Blade jamming handling (Fig. U)
- Ensure the machine is disconnected from the power
source.
Caution: (Fig. Q)
- Always use the push stick (19) when ripping small
workpieces (fig. Q)
- Do not cut excessively small workpieces.
Cross Cutting
- Lock the miter gauge (6) at 0 degree
- Set the bevel angle to 0 degree
- Adjust the saw blade (4) height
- Hold the workpiece flat on the table (1) and against the
fence. Keep the workpiece away from the blade.
- Keep both hands away from the path of the saw blade.
- Switch the machine on and allow the saw blade to reach
full speed.
- Hold the workpiece tightly again the fence and slowly
move the workpiece together with the fence assembly until
the workpiece comes underneath the upper blade guard.
Allow the teeth to cut, and do not force the workpiece
through the saw blade. The saw blade speed should be
kept constant.
After completing the cut, switch the machine off, allow the saw
blade to stop and remove the workpiece
- Push the and the workpiece toward the blade in order to
make the cut.
Important: Never push or hold the cut-off-side workpiece.
Bevel cuts (Fig. R)
Bevel cuts must always be made using the rip fence (5).
- Set the blade (4) to the desired angle.
P
5
3
2
4 1
Q
19
R
621a 21b4
S
6
T
2
19
11


Need help? Post your question in this forum.

Forumrules
1

Forum

stanley-sst1800

Reset search

  • which screw to open to adjust the saw blade with the table slot? Submitted on 9-10-2022 at 02:28

    Reply Report abuse
  • where to align the saw blade with the table slot for stanley SST1800w?
    Submitted on 9-10-2022 at 02:20

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SST1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SST1800 in the language / languages: English, French as an attachment in your email.

The manual is 5,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info