720738
9
Zoom out
Zoom in
Previous page
1/36
Next page
(Original instructions) ENGLISH
9
Setting the angle (Fig. J)
Set the required bevel angle from 0 to 45 degree
Before cutting, ensure the saw blade (4) and mitre
gauge (6) no collision
- Loose the Bevel adjustment locking knob (10).
- Set up the desired angle then lock the knob again
Working with the rip fence
Setting the fence height (Fig. K)
- The fence rail (i) of the rip fence (5) has two guiding
surface with different heights.
- Depending on the thickness of the material to be cut, the
higher side of the fence rail (i) has to be used for thick
material (work piece thickness above 25mm) and the
lower side of the fence rail for thin material (work piece
thickness below 25mm).
- For the adjustment, loosen the bolts on the side of the rip
fence (5) and push the fence rail (i) on he guide,
depending on the required position.
- Tighten the bolts again.
Rip fence assembly (Fig. L)
- Fix the rip fence (5) at the back side and press the locking
handle (15) downwards.
- When disassembly, pull the locking handle up and remove
the rip fence (5).
- The rip fence could be locked setting with the rear knurled
nut.
5. Warning! Turn the nut in the rotational direction of the saw
blade.
6. Remove the outer flange and take out the saw blade from
the inner flange, with diagonally downwards movement.
7. Carefully clean the flange with a before fixing the new saw
blade.
8. Insert the new saw blade and fasten the outer flange. The
outer flange has a Φ30mm raised boss which fits in side
the blade bore.
Warning! The teeth of a new blade are very sharp and can be
dangerous. Make sure the teeth point down at the front of the
table, aligned with the arrow marked on the saw blade guard
(2).
9. Attach the table insert (20) and the saw blade guard (2)
again and set them.
10. Before working, check the functionality of the guards.
On/Off switch (Fig. J)
- To switch the machine on, press the green start “I” button.
- To switch the machine off, press the red stop “O” button.
Cutting depth (Fig. J)
Turn the blade elevation handle (11) to set the blade to the
required cutting depth.
- Turn anti-clockwise; to increase the cutting depth
- Turn Clockwise; to reduce the cutting depth
After each new adjustment it is advisable to carry out a trial
cut in order to check the set dimensions.
I
17 17
J
8
11
10
K
i5
L
515
9


Need help? Post your question in this forum.

Forumrules
1

Forum

stanley-sst1800

Reset search

  • which screw to open to adjust the saw blade with the table slot? Submitted on 9-10-2022 at 02:28

    Reply Report abuse
  • where to align the saw blade with the table slot for stanley SST1800w?
    Submitted on 9-10-2022 at 02:20

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SST1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SST1800 in the language / languages: English, French as an attachment in your email.

The manual is 5,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info