Manual Stanley SST1800 (page 8 of 36) (English, French)

720738

Zoom out

Zoom in

1/36

ENGLISH (Original instructions)

4. The gap between the saw blade (4) teeth and the riving

knife should be around 3mm to 5mm (Fig.G)

5. R-tighten the mounting screw (f) and ﬁx the table insert

(20)

Warning! Ensure the machine is disconnected from

the power source. Never user the machine without

the table insert; Immediately replace the table insert

when worn or damaged

Saw blade guard assembly (Fig. H)

1. Fasten the saw blade guard (2) to the riving knife (5) with

the bolt (g).

2. Place the rear extraction hose (h) on the extraction

adapter on the saw blade guard (2).

3. Disassembly in reverse order.

Saw blade assembly/replacement (Fig. E, H, I)

1. Warning: Ensure the machine is disconnected from the

power source. Wear the safety gloves.

2. Disassemble the saw blade guard (2) (Fig. H.)

3. Remove the table insert (20) (Fig. E).

4. Loosen the nut by placing the spanner wrench (17) on the

nut and countering with another spanner wrench (17) on

the ﬂange (Fing. I).

Riving knife set-up (Fig. E, F, G)

Warning! Disconnect the mains cable! The setup

of the riving knife (3) must be checked before

each use.

1. Set the saw blade (4) to the max. cutting depth, put it at 00

position and lock it

2. Remove the table insert (20) (Fig. E)

Warning! For transport reasons, the riving knife

(3) was ﬁxed in the lower position before initial

commissioning. Only work with the machine if

the riving knife (3) is in the upper position.

Fitting the riving knife (3) in the upper position

is as follows:

3. Loosen the locking handle (f) and push the riving knife (3)

in the upper position (Fig.F)

204

max. 3-5 mm

2 3

which screw to open to adjust the saw blade with the table slot? Submitted on 9-10-2022 at 02:28
Reply Report abuse
where to align the saw blade with the table slot for stanley SST1800w?
Submitted on 9-10-2022 at 02:20
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SST1800 in the language / languages: English, French as an attachment in your email.

The manual is 5,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SST1800 Manual

Product: