720577

Stanley SPS-900 Manual

17
Zoom out
Zoom in
Previous page
1/36
Next page
17
- Carefully advance the trimming line to an obstacle, and
use the tip of the line to cut around the obstacle. When
the trimming line comes into
contact with stones, trees, and walls, the line wears
out or breaks off ahead of time. In this case, this can be
happened that the yarn disappeared into the string spool
housing and the trim line automatic transmission does
not work anymore.
- Swing the petrol cutting blade like a normal scythe
horizontally from right to left and
back again. You define the cutting height depending on
how high you are holding the tool.
- Never replace the nylon line with a metal wire.
RISK OF INJURIES
Using Cutting Blade for Cutting
- Use the cutting blade to comb through brushwood, rank
growth, young tree populations
(trunk diameter of maximum 2 cm), and high grass.
- While using metal cutting tools, there is generally
a risk of recoil, when the tool hits a solid obstacle
(stones, trees, branches, etc.). Thereby, the tool is hurled
backwards against the rotating direction.
- To cut rank growth and brushwood, you “immerse” the
cutting blade from the top. This way, the objects to be
cut will be chaed.
CAUTION: Be especially careful, when using this
working technique, because the further away the
cutting tool is from the ground, the higher is the
risk that objects to be cut and particles will be
hurled sideways.
- To comb through young tree populations and to
cut grass, move the tool like a scythe closely above the
ground.
CAUTION: Incorrect use and misuse can damage the
bush cutter and cause severe injuries because of pieces
hurled away.
- To minimize the risk of accidents by use of the
cutting blade, take note of following points:
- Never cut shrubbery or wood whose diameter is
larger than 2 cm.
- Avoid contact with metal bodies, stones, etc.
- Periodically check the cutting blade for damages.
Never continue to use a damaged cutting blade.
- When the cutting blade becomes apparently blunt, it
must be sharpened according to instructions.
When the cutting blade is apparently out of balance, it
must be replaced.
Automatic Feeding of Trimming Line
To extend the cutting line(22), run the engine at full
speed and tap the line spool on the ground. This will
automatically extend the line. The blade on the guard
hood will cut the line to the permissible length.
Replacing the line spool/ cutting line
-Dismantle the line spool. Press the spool and remove
one half of the housing.
- Take the spool plate(k) out of the line spool
housing(B25).
- Place the new cutting line in the center and hang the
loop which has formed into the recess in the Spool
splitter(B26).
-Wind up the line counter-clockwise and under tension.
The spool splitter will separate the two halves of the
line.
-Hook the last 15cm of the two ends of the line onto the
opposite lying line holders of the spool plate(B28).
-Thread the two ends of the line through the metal
eyelets in the line spool housing(B25).
-Press the spool plate into the line spool housing
-Pull the two line ends sharply to release them from the
line holders.
-Join the housing parts together again
-Cut the excess line to a length of around 13cm. this
will reduce the load on the engine when starting and
warming up.
-Refit the line spool.
G
B
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SPS-900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SPS-900 in the language / languages: English, German as an attachment in your email.

The manual is 3,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info