720577
15
Zoom out
Zoom in
Previous page
1/36
Next page
15
hexagonal screw on the shaft in anti-clockwise
direction, and use the supplied hexagonal
wrench (15) to tighten this screw (B13).
CAUTION: Left-handed Thread
Assembly of Carrying Strap (B14 - B16)
The petrol cutting blade must be used with a
carrying strap (17).
First, balance the petrol brush cutter
when the tool is swithced off.
- Wear the shoulder strap (17).
- Adjust the strap length so that the snap hook is
roughly one hand below the right hip (B14).
- Hook the petrol cutting blade into the snap hook.
- Let the petrol cutting blade swing.
When standing in a normal working posture, the
cutting tool should just touch the ground (B15).
- You may use an Allen key to loosen the bracket, if
necessary, and shift forwards or backwards.
Thereby, it is important that the petrol brush cutter is
always well balanced (B16).
For operation, hook the petrol brush cutter
into the snap hook of the carrying strap
while the engine is running.
Safety strap on the carrying strap (B40)
ATTENTION! In an emergency, the safety strap (26) can
be pulled on the carrying strap (17), see Figure B16. Then
the machine releases immediately from the carrying
strap (17) and falls to the ground(B16).
Fuel
Only use a mix of unleaded regular gasoline and
2-stroke special engine oil in a mix ratio of 40:1.
Caution: Do not use any other mix ratio and do not use
pure gasoline.
Do not use any fuel older than 2-3 months.
Empty the tank when taking longer breaks, and
refill before start of work.
Gasoline Mix
4,0 liters of gasoline and 100 ml of 2-stroke special
engine oil (filling station)
- Fill 4,0 liters of gasoline into a fuel tank together with
100 ml 2-stroke engine oil and mix both by shaking the
tank vigorously.
- Fill the fuel into the tank and close the cap.
Filling up Gasoline
- Slowly turn the tank cap to open it, so that
pressure and gasoline vapor can escape in a
non-hazardous manner.
- Use a funnel to fill up the 2-stroke oil mixed with
gasoline in a ratio of 40:1, and tighten the cap again.
Starting when Engine is Cold
- Place the petrol cutting blade safely on the ground.
Fuel tank and cutting guard are used as support.
Make sure that the cutting tool does not come into
contact with either the ground, or any other
objects.
- Move the operating switch (4) at the operating
handle down (B17).
- Move the choke lever (B18) up:
- Press the injection valve (24) and hold it, until the
transparent gasoline tube fills with gasoline (B19).
- Use your right hand to clasp the operating
handle (3). Thereby, you will unlock the locking
device (5) of the throttle control.
- Strongly press the throttle control (6).
- At the same time, press the operating switch and the
G
B
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SPS-900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SPS-900 in the language / languages: English, German as an attachment in your email.

The manual is 3,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info