720577
13
Zoom out
Zoom in
Previous page
1/36
Next page
13
Never cut against hard objects such as stone, etc.
This way you avoid injuries, and damages to the tool.
Never use the tool without the guards attached.
Never use your hands to stop the cutting device.
Always wait until it stops on its own.
Hold and guide the trimmer head as close to the
ground as possible.
Only cut grass growing on the ground. Do not cut
Dgrass in cracks in walls, growing or on rocks, etc.
Always make sure no objects, or other debris is
collecting in the trimmer head, in the protective
hood, or in the engine.
Only use the tool, when the guard is attached.
Always switch off the tool, before you put it down.
Keep in mind that there is risk of injuries in the area of
the cutting device intended to cut off the line.
CAUTION: The cutting tool continues rotating for a few
seconds after the engine is turned off.
Put the tool down only after the cutting tool has
completely stopped and the motor is turned off.
When the cutting tool is damaged, it must be
replaced at once.
Always use the original line only. Never use a metal wire
instead of the nylon line.
Tool and cutting tools must be properly inspected
and serviced periodically. Damages must be
repaired by a service center.
Only use accessories recommended by the
manufacturer.
Have your tool serviced only by qualified personnel and
by use of original spare parts only.
This ensures that the tool will work safely in the future.
Overview of Tool Components (A1)(B1)
1. Clamp screws for handrail holder
2. Handlebar
3. Operating handle
4. Operating switch
5. Locking device
6. Throttle lever
7. Suspension Harness
8. Air filter
9. Engine
10. Fuel tank
11. Cutting blade
12. Cutting guard
13. Trimmer head
14. Allen key
15. Spark plug wrench
16. Gasoline Blending tank
17. Carrying strap
18. Screwdriver
19. Locking screw
20. Retention pin
21. Cutting line
22. Spark plug
23. Choke lever
24. Injection valve
25. Starter Seil
26. Safety latch
Assembly
Check if all parts are included and if they were
damaged during transport before assembly.
1. Place the tool horizontally with the engine facing
towards the ground.
2. Release the clamp screw (19) (A1), and insert the top
and bottom Trimmer tube into the provided connector
(A2).
3. Slightly twist the bottom Trimmer tube to
engage the retention pin (20) in the bore hole of
the connector. Then tighten the clamp screw.
4. To disassemble, loosen the clamp screw, push
the retention pin inwards, and pull the Trimmer
tube apart (A4).
G
B
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SPS-900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SPS-900 in the language / languages: English, German as an attachment in your email.

The manual is 3,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info