720577
18
Zoom out
Zoom in
Previous page
1/36
Next page
18
CAUTION:when you operate the machine please
avoid the contact with curbs, stones and other hard
objects, because the cutting line may break and the
trim line automatic stops working.
Maintenance and Care
Gear Lubrication
Check the filling of lubrication grease every 25
hours of operation.
- Use an Allen key to remove the plug screw by
turning (B29).
- When you cannot see any grease on the screw,
fill approx. 5 g lubrication grease (DIY store) into
the gearbox case, and close the ller opening again.
Keep in mind that the gearbox case should never
be completely filled with lubrication grease.
Air filter
After working for longer time, you should clean the air
filter. Dust and pollen plug up the pores of the filter made
of foamed plastic.
- Remove the cover (B30), and wash the filter (B31)
in mild soap water. Caution: Do not use any
gasoline or solvent.
- Dry the filter before you insert it again.
In order not to shorten the service life of the engine, a
damaged air filter must be replaced at once.
Adjustment of Spark Plug
Check the spark plug air gap at least once a year or when
the engine starts poorly. The correct gap
between ignition flag and ignition contact
is 0.6-0.7 mm (B32).
- Wait until the engine has cooled down completely.
- Loose the screw and remove the plastic cover (B33).
- Pull the spark plug cap (B34) off the spark plug,
and use the supplied spark plug wrench to
remove the spark plug by turning (B35).
- When the electrode is severely worn out or
reveals a strong incrustation, the spark plug must
be replaced with an equivalent plug.
A strong incrustation of the spark plug can be
caused by: Amount of oil is too high in the
gasoline mix, poor oil quality, old gasoline mix, or
plugged up air filter.
- Screw the spark plug by hand completely into the
thread. (Avoid jamming it)
- Use the supplied spark plug wrench to tighten the spark
plug.
- When using a torque wrench, the tightening
torque is 12-15 Nm.
- Plug the spark plug socket correctly on the plug.
Trimming the Line Knife
- When the trimming line is no longer cut clean
during feeding, use a file to re-sharpen the cutting edge
(B36). File in one direction and in the
specified angle.
Cleaning
Use a moist piece of cloth to clean the plastic parts.
Do not use any cleaning agents, solvents, or sharp
objects.
During the course of work, wet grass and weed
wraps around the drive shaft below the cutting
guard for technical reasons. Remove this, otherwise the
engine will overheat because of too much friction.
Periodical Checks
Keep in mind that following specifications relate to
normal usage. Owing to circumstances (longer
periods of daily work, severe dust exposure, etc.),
the specified intervals will become correspondingly
shorter.
G
B
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SPS-900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SPS-900 in the language / languages: English, German as an attachment in your email.

The manual is 3,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info