622250

Stanley SML 77-322 Manual

11
Zoom out
Zoom in
Previous page
1/208
Next page
11
77-322
Level Adjustment
• For easy reference, position the leg base in such a way that
the circular bubble is above one of the adjustable legs.
• The circular bubble should be centered in the vial.
• If adjustment is required, proceed as follows
(See Figure
F
) :
• Turn the rear adjustable legs to bring the circular
bubble to the edge of the vial as indicated.
• Center the circular bubble by turning the front
adjustable leg.
Operation
NOTE:
• See LED Descriptions for indications during operation.
• Before operating the laser tool always be sure to check the
laser tool for accuracy.
• In Manual Mode, Self-Levelling is OFF. The accuracy of the
beam is not guaranteed to be level.
• Laser tool will indicate when it is out of compensation
range. Reference LED Descriptions. Reposition laser tool
to be closer to level.
• When not in use, please be sure to power OFF the laser
tool and place the pendulum lock in the locked position.
Power
• Press
to turn laser tool ON.
• To turn laser tool OFF, repeatedly press
until the
OFF mode is selected OR press and hold
for ≥ 3
seconds to turn laser tool OFF while in any mode.
Mode
• Press
repeatedly to cycle through the available
modes.
Self-Levelling / Manual Mode (See Figure
H
)
• The pendulum lock on the laser tool needs to be
switched to the unlocked position to enable self-
levelling.
• The laser tool can be used with the pendulum lock in
the locked position when it is required to position the
laser tool at various angles to project non-level / plumb
straight lines or points.
Pulse Mode (See Figure
J
)
• When laser tool is ON, press
to turn ON / OFF
pulse mode.
• Pulse mode allows use with laser detector.
Applications
Plumb / Point Transfer
• Using the vertical laser beam, establish a vertical reference
plane.
• Position the desired object(s) until they are aligned with the
vertical reference plane to ensure object(s) are plumb.
• Establish 2 reference points that need to be plumb.
• Align either the down laser beam or the up laser cross to a
set reference point.
• The opposing laser beam(s) will be projecting a point which
is plumb.
• Position the desired object until the laser beam is aligned
with the second reference point that needs to be plumb
with the set reference point.
Level / Point Transfer
• Using the horizontal laser beam, establish a horizontal
reference plane.
• Position the desired object(s) until they are aligned with the
horizontal reference plane to ensure object(s) are level.
Square
• Using either of the vertical laser beams that cross the
horizontal laser beams, establish a point where the 2
beams cross.
• Position the desired object(s) until they are aligned with
both the vertical and horizontal laser beams to ensure
object(s) are square.
Pulse Mode (See Figure
J
)
• Setting laser tool to pulse mode allows use with optional
laser detectors.
Manual Mode (See Figure
H
)
• Disables self-levelling function and allows laser unit to
project a rigid laser beam in any orientation.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SML 77-322 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SML 77-322 in the language / languages: All languages as an attachment in your email.

The manual is 3,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info