622250

Stanley SML 77-322 Manual

10
Zoom out
Zoom in
Previous page
1/208
Next page
10
77-322
Charging Battery
• For best life, the rechargeable battery must be charged for
4 hours before fi rst use.
• Plug charging / power adapter plug into charging jack of
laser tool
• Plug charging / power adapter into power outlet (110 V or
220 V) with appropriate plug receptacle.
• The LED on the charging / power adapter will light RED
during charge.
• Leave battery to charge for approximately 4 hours to reach
full charge.
• When battery is fully charged unplug the charging / power
adapter from laser tool and power outlet.
• The LED on the charging / power adapter will light GREEN
when charge is complete.
WARNING:
• Use charging / power adapter only with Ni-MH
battery pack supplied. Charging any other
type of battery may result in damage and/or
personal harm.
WARNING:
• The battery and charging / power adapter can be
damaged if damp. Always store and charge the
tool in a dry and covered place.
NOTE:
• For best battery life, it is recommended to charge the
battery once it has been fully discharged and avoid letting
charge for > 10 hours at a time.
Operating with Charging / Power
Adapter
• Laser tool can operate while plugged into charging / power
adapter.
• Functions and controls of laser tool are the same as when
not plugged into charging / power adapter.
Set Up
Mounting on Accessories
Legs (See fi gure
D
)
• The legs on the laser tool can be removed to allow the
laser tool to be directly placed on a surface and / or
accessory.
• Remove leg base screw to release the leg base from
the main laser tool.
• If attaching the laser tool to an accessory, re-insert
the leg base screw into the laser tool to connect to a
5/8 center screw thread.
• To attach the leg base to the laser tool:
• Remove the leg base screw, if it is on the laser tool.
• Place the leg base screw up through the center hole
in the leg base attachment.
• For easy reference, position the leg base in such
a way that the circular bubble is above one of
the adjustable legs as shown (See Figures
D
and
A
).
• Tighten the leg base screw.
Tripod / Accessory Mount (See fi gure
E
)
• Position a tripod / accessory in a place where it will not
be easily disturbed and near the central location of the
area to be measured.
• Set up the tripod / accessory as required. Adjust
positioning to be sure tripod head / accessory mounting
base is near horizontal.
• Remove the leg base attachment from the laser tool, as
instructed above, for easier mounting.
• Mount the laser tool to the tripod / accessory by pushing
up the 5/8 center screw and tighten (An adapter will be
required for accessories with 1/4 thread screw).
CAUTION:
• Do not leave the laser tool unattended on an
accessory without fully tightening the center
screw. Failing to do so may lead to the laser tool
falling and sustaining possible damage.
NOTE:
• It is best practice to always support laser tool with
one hand when placing or removing laser tool from an
accessory.
• If positioning over a target, partially tighten the center
screw, align laser tool, and then fully tighten.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SML 77-322 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SML 77-322 in the language / languages: All languages as an attachment in your email.

The manual is 3,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info