720743

Stanley FMHT1-77416 Manual

12
Zoom out
Zoom in
Previous page
1/212
Next page
12
GB
6.
On the ceiling, mark two short lines
b
and
c
where the
front and side laser beams cross.
7.
Pick up and rotate the laser 180º, and position the down
dot directly over
a
, the previous position of the down dot,
as shown in Figure
G
#3.
8.
On the ceiling, look at the position of the two laser beams.
If they are not parallel to marked lines
b
and
c
, turn the
laser until the laser beams are closely lined up with
b
and
c
.
9.
On the ceiling, mark two short lines
d
and
e
where the
beams cross.
10.
Measure the distance between marked lines
b
and
d
,
and marked lines
c
and
e
.
11.
If your measurement is greater than the Allowable
Distance Between Marked Lines for the corresponding
Ceiling Height in the following table, the laser must be
serviced at an authorized service center.
Ceiling Height
Allowable Distance
Between Marked Lines
2.5m (8′) 1.5mm (1/16")
3m (10′) 2.0mm (3/32”)
4m (14′) 2.5mm (1/8”)
6m (20′) 4mm (5/32”)
9m (30′) 6mm (1/4”)
90º Between Vertical Beams
Checking 90º accuracy between the front and side vertical
beams requires an open oor area at least 6m x 3m (20′ x 10′).
1.
Place the laser on a smooth, at, stable surface that is
level in both directions, as shown in Figure
H
#1.
2.
Turn the laser ON.
3.
Press three times to display the front and side vertical
beams.
4.
Press twice to display the down dot.
5.
Along the front laser beam, mark three locations
a
,
b
, and
c
; where
b
is at the midpoint of the laser beam.
6.
Position the laser so the down dot is over
b
and the front
laser beam is aligned with
c
(Figure
H
#2).
7.
Mark a location
e
along the side laser beam at least 3m
(10’) away from the laser.
8.
Turn the laser clockwise 90º.
9.
Position the laser so the down dot is over
b
and the front
laser beam is aligned with
e
(Figure
H
#3).
10.
Along the side laser beam, mark
f
near
a
.
11.
Measure the distance between
a
and
f
.
12.
If your measurement is greater than the Allowable
Distance Between
a
&
f
for the corresponding
Distance from
b
to
a
in the following table, the laser
must be serviced at an authorized service center.
Distance from
b
to
a
Allowable Distance
Between
a
&
f
3m (10′) 3.2mm (1/8”)
4m (14′) 3.5mm (5/32”)
5m (17′) 4.5mm (3/16”)
6m (20′) 5.5mm (7/32”)
7m (23′) 6mm (1/4”)
Using the Laser
Operating Tips
• Always mark the center of the beam created by the laser.
• Extreme temperature changes may cause movement of
internal parts that can affect accuracy. Check your accuracy
often while working.
• If the laser is ever dropped, check to make sure it is still
calibrated.
• As long as the laser is properly calibrated, the laser is self-
leveling. Each laser is calibrated at the factory to nd level as
long as it is positioned on a at surface within average ± 4°
of level. No manual adjustments are required.
• Use the laser on a smooth, at, level, surface.
Turning the Laser Off
Slide the Power/Transport Lock switch to the OFF/Locked
position (Figure
A
#1a) when the laser is not in use. If the
switch is not placed in the Locked position, the laser will not
turn off.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMHT1-77416 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMHT1-77416 in the language / languages: All languages as an attachment in your email.

The manual is 18,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info