720743

Stanley FMHT1-77416 Manual

10
Zoom out
Zoom in
Previous page
1/212
Next page
10
GB
4.
Push the battery compartment cover closed until it snaps in
place (Figure
B
#3).
5.
Slide the Power/Transport Lock switch to the right to the
Unlocked/ON position (Figure
A
#1b).
6.
On the keypad, make sure (Figure
A
#3) is not
ashing (> 5%). If is ashing, this means that the
battery level is below 5%.
• The laser may continue to operate for a short time while
the battery power continues to drain, but the laser lines
and dots will quickly dim.
• After fresh batteries are installed and the laser is turned
ON again, the laser lines and dots will return to full
brightness.
7.
When the laser is not in use, slide the Power/Transport
Lock switch to the LEFT to the Locked/OFF position
(Figure
A
#1a) to save battery power.
Using the Mounting Block
On the bottom of the laser is a moveable block (Figure
D
).
• To use the magnets on the front of the laser (Figure
A
#2) to
mount the laser against the side of a steel beam, do not
extend the moveable block (Figure
D
#1). This will allow the
down dot to be aligned with the edge of the steel beam.
• To mount the laser over a point on the oor (using a multi-
function bracket or a tripod), pull out the moveable block until
it clicks in place (Figure
D
#2). This will allow the laser down
dot to display through the 5/8-11 mounting hole and the laser
to be rotated over the 5/8-11 mounting hole without moving
the vertical position of the laser.
Turning the Laser On
1.
Place the laser on a smooth, flat, level surface, with the
laser facing straight ahead toward the opposing wall
(0º position).
2.
Slide the Power/Transport Lock switch to the right to the
Unlocked/ON position (Figure
A
#1b).
3.
Press (Figure
A
#6) once to display a horizontal laser
line, a second time to display a down dot, and a third time
to display a horizontal line and a down dot.
4.
Check the laser beams. The laser is designed to self-level.
• If the laser is tilted so much that it cannot self-level
(> 4°), the laser beams will continually flash twice and
(Figure
A
#4) will flash constantly on the keypad.
• If the laser beams ash, the laser is not level (or plumb)
and should NOT BE USED for determining or marking
level or plumb. Try repositioning the laser on a level
surface.
5.
Press (Figure
A
#5) once to display a vertical laser
line from the front of the laser, a second time to display
a vertical laser line from the side of the laser, and a third
time to display both vertical lines.
6.
Press (Figure
A
#7) to test the Pulse mode. will
illuminate and the laser beams will appear lighter, since
they are ashing at a very rapid rate. You will only use
Pulse mode with a detector to display the laser beams long
range.
7.
If ANY of the following statements are TRUE, continue with
the instructions for Checking Laser Accuracy BEFORE
USING THE LASER for a project.
• This is the first time you are using the laser (in case
the laser was exposed to extreme temperatures).
• The laser has not been checked for accuracy in
a while.
• The laser may have been dropped.
Checking Laser Accuracy
The laser tools are sealed and calibrated at the factory. It
is recommended that you perform an accuracy check prior
to using the laser for the rst time (in case the laser was
exposed to extreme temperatures) and then regularly to
ensure the accuracy of your work. When performing any of
the accuracy checks listed in this manual, follow these
guidelines:
• Use the largest area/distance possible, closest to the
operating distance. The greater the area/distance, the
easier to measure the accuracy of the laser.
• Place the laser on a smooth, at, stable surface that is
level in both directions.
• Mark the center of the laser beam.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMHT1-77416 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMHT1-77416 in the language / languages: All languages as an attachment in your email.

The manual is 18,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info