720743

Stanley FMHT1-77416 Manual

11
Zoom out
Zoom in
Previous page
1/212
Next page
11
GB
Horizontal Beam - Scan Direction
Checking the horizontal scan calibration of the laser requires
two walls 9m (30′) apart. It is important to conduct a calibration
check using a distance no shorter than the distance of the
applications for which the tool will be used.
1.
Place the laser against the end of a 9m (30′) wall
(Figure
E
#1).
2.
Turn the laser ON.
3.
Press once to display a horizontal laser beam.
4.
Turn the laser toward the opposite end of the wall and
parallel to the adjacent wall.
5.
At least 9m (30′) apart on the laser beam, mark
a
and
b
.
6.
Turn the laser 180º.
7.
Adjust the height of the laser so the center of the beam is
aligned with
a
(Figure
E
#2).
8.
Directly above or below
b
, mark
c
along the laser beam
(Figure
E
#3).
9.
Measure the vertical distance between
b
and
c
.
10.
If your measurement is greater than the Allowable
Distance Between
b
and
c
for the corresponding
Distance Between Walls in the following table, the laser
must be serviced at an authorized service center.
Distance
Between Walls
Allowable Distance
Between
b
and
c
9m (30′) 6mm (1/4”)
12m (40′) 8mm (5/16”)
15m (50′) 10mm (13/32”)
Horizontal Beam - Pitch Direction
Checking the horizontal pitch calibration of the laser requires
a single wall at least 9m (30′) long. It is important to conduct
a calibration check using a distance no shorter than the distance
of the applications for which the tool will be used.
1.
Place the laser against the end of a 9m (30′) wall
(Figure
F
#1).
2.
Turn the laser ON.
3.
Press once to display a horizontal laser beam.
4.
Turn the laser toward the opposite end of the wall and
parallel to the adjacent wall.
5.
At least 9m (30′) apart on the laser beam, mark
a
and
b
.
6.
Move the laser to the opposite end of the wall
(Figure
F
#2).
7.
Position the laser toward the rst end of the same wall and
parallel to the adjacent wall.
8.
Adjust the height of the laser so the center of the beam is
aligned with
b
.
9.
Directly above or below
a
, mark
c
along the laser beam
(Figure
F
#3).
10.
Measure the distance between
a
and
c
.
11.
If your measurement is greater than the Allowable
Distance Between
a
and
c
for the corresponding
Distance Between Walls in the following table, the laser
must be serviced at an authorized service center.
Distance Between
Walls
Allowable Distance
Between
a
and
c
9m (30′) 6mm (1/4”)
12m (40′) 8mm (5/16”)
15m (50′) 10mm (13/32”)
Vertical Beam - Plumb
Checking the vertical (plumb) calibration of the laser can be
most accurately done when there is a substantial amount of
vertical height available, ideally 9m (30′), with one person on
the oor positioning the laser and another person near a ceiling
to mark the position of the beam. It is important to conduct
a calibration check using a distance no shorter than the distance
of the applications for which the tool will be used.
1.
Place the laser on a smooth, at, stable surface that is
level in both directions (Figure
G
#1).
2.
Turn the laser ON.
3.
Press three times to display the front and side vertical
beams.
4.
Press twice to display the down dot.
5.
On the level surface, mark the position of the down dot
a
(Figure
G
#2).
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMHT1-77416 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMHT1-77416 in the language / languages: All languages as an attachment in your email.

The manual is 18,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info