708059
15
Zoom out
Zoom in
Previous page
1/42
Next page
15


The Model Name function allows you to name a model using up to 10 characters.
This makes identifying and selecting models much easier. Naming a model is
normally done during initial setup. You can modify or change names at any time
without affecting other programming. Typical model names include Vibe 50 3D,
Extra 300, Blade 400, Sport 40 #1, etc. Note that upper case, lower case, numbers
and symbols are available.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Model Name then press to access the function.
The following screen appears:
Rotate the roller to highlight the desired character then press to accept.
Repeat the process until complete. The name will display on the main screen.
Pressing  will erase the current character.

Use the Wing Type function to program the wing and tail mix to match your
airplane. Eight wing types (Normal, elevon, dual aileron, 1 aileron and 1 flap,
flaperon, 1 aileron and 2 flaps, 2 ailerons and 1 flap, 2 ailerons and 2 flaps) and
five tail types (normal, V-Tail, dual elevator, dual rudder, dual rudder/ elevator) are
available. You must select the correct wing and tail type to match your airplane
before doing any other wing or tail related programming (e.g., Flaps, Travel
Adjust, Sub-Trim, etc.).

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Wing Type then press to access the function.
The following screen appears:
Rotate the roller to highlight Wing and press to access the function. Rotate the
roller to the desired wing mix. Press the roller to select.

Rotate the roller to highlight Tail then press.
Rotate the roller to access the desired tail type. Press the roller to select.

The Switch Select function allows the switches, knob and right and left trimmers
to be assigned to the gear, Aux1, Aux2 or Aux3 channels or inhibit.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight the desired switch, knob or trimmer then press the
roller to access.
Rotate the roller to select the desired channel or function you wish the switch,
knob or trimmer to operate. Press the roller to accept. Note that the channel or
function can only be assigned once.
Repeat to select all desired switch positions.

Use the Swash Type screen to program the swashplate mix to match your
helicopter swashplate type. Six swashplate types are available: Normal, 3-servo
120 CCPM, 3-servo 140 CCPM, 3-servo 90 CCPM, 3-servo 135 CCPM, and
2-servo 180 CCPM. Select the correct swashplate type to match the specific
helicopter before doing any other cyclic programming e.g., Pitch Curve, Travel
Adjust, Sub-Trim, etc.). If in doubt consult your helicopter’s manual for correct
swashplate mixing.
EN
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spektrum DX8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX8 in the language / languages: English as an attachment in your email.

The manual is 5,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX8

Spektrum DX8 Quick start guide - English - 100 pages

Spektrum DX8 User Manual - German - 42 pages

Spektrum DX8 User Manual - French - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info